D-Link WAP54G manual Connecting Wireless-G Access Point, Wireless-G Access Point’s Front Panel

Page 44

Instant Wireless® Series

T

The Wireless-G Access Point’s Front Panel

 

Figure 3-2

Power

Green. The Power LED lights up when the Access Point is

 

powered on.

Diag

Red. The Diag LED indicates the Access Point’s self-diagnosis

 

mode during boot-up and restart. It will turn off upon com-

 

pleting the diagnosis. If this LED stays on for an abnormally

 

long period of time, refer to the Troubleshooting Appendix.

WLAN Act

Green. If the WLAN’s Act LED is flickering, the Access Point

 

is actively sending or receiving data to or from one of the

 

devices on the network.

WLAN Link

Green. The WLAN’s Link LED lights whenever there is a suc-

 

cessful wireless connection.

LAN Act/Link Green. The LAN’s LINK LED serves two purposes. If the LED is continuously lit, the Access Point is successfully con- nected to a device through the LAN port. If the LED is flick- ering, it is an indication of any network activity.

LAN Full/Col Green. The LAN’s Full/Col LED also serves two purposes. When this LED is continuously lit, the connection made through the corresponding port is running in Full Duplex mode. A flickering LED indicates that the connection is expe- riencing collisions. Infrequent collisions are normal. If this LED blinks too often, there may be a problem with your con- nection. Refer to the Troubleshooting Appendix if you think there is a problem.

LAN 100 Orange. The LAN’s 100 LED indicates when a successful 100Mbps connection is made through the LAN port.

Wireless-G Access Point

Chapter 4: Connecting the

Wireless-G Access Point

1.Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations.

2.Fix the direction of the antenna. Try to place it in a position which can best cover your wireless network. Normally, the higher you place the anten- na, the better the performance will be. The antenna’s position enhances the receiving sensitivity.

3.Connect a standard Ethernet network cable to the Access Point. Then, connect the other end of the Ethernet cable to a switch or hub. The Access Point will then be connected to your 10/100 Network.

4.Connect the AC Power Adapter to the Access Point’s Power port and plug the other end into an electrical outlet. Only use the power adapter supplied with the Access Point. Use of a different adapter may result in product damage.

Now that the hardware installation is complete, proceed to Chapter 5: Setting Up the Wireless-G Access Point for directions on how to set up the Access Point.

Note: In order for all other wireless devices to communicate with the Access Point, those devices must be operating in Infrastructure Mode. If any wireless devices are configured in Ad Hoc Mode, they will not be recognized by the Access Point.

4

5

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Wireless-G Access Point Table of Contents Mail Package Contents Connecting the Wireless-G Access PointSetting up the Wireless-G Access Point Ssid Instant Wireless Series Copyright & Marques DE Commerce Table des matières Contenu de l’emballage Étape 1 Branchement du point d’accès sans fil GÉtape 2 Configuration du point d’accès sans fil G Ssip WEP Copyright & Marken Inhalt Schritt 1 Anschließen des Wireless-G Access Point LieferumfangSchritt 2 Einrichten des Wireless-G Access Point Enter Network S s w o r d Exit Copyright & Marchi Indice Fase 1 collegamento di Wireless-G Access Point Contenuto della confezioneFase 2 configurazione di Wireless-G Access Point Password Dell’utilità basata sul Se è Stata immessa Una Passphrase, la chiave Direitos DE Autor E Marcas Comerciais Índice Conteúdo da embalagem Passo 1 Ligar o Ponto de acesso sem fios-GPasso 2 Configurar o Ponto de acesso sem fios-G Password Palavra Setup Wizard Assistente Copyright Y Marcas Registradas Contenido Paso 1 Conexión del punto de acceso Wireless-G Contenido del paquetePaso 2 Configuración del punto de acceso Wireless-G Ssid Siguiente Copyright 2003 Linksys, All Rights Reserved Wireless-G Access Point Latan-soporte@linksys.com Introduction Introduction Instant Wireless Wireless-G Access PointFeatures Planning Your Wireless Network Getting to Know the Wireless-G Access PointWireless-G Access Point’s Back Panel Network TopologyConnecting Wireless-G Access Point Wireless-G Access Point’s Front PanelSetting Up Wireless-G Access Point Instant Wireless Series Instant Wireless Series Instant Wireless Series Configuring Wireless-G Access Point Setup TabWireless Password Tab SETTINGThe AP ModeTHE APTabMODEStatus Tab Log Tab Help Tab Filter TabAdvanced Wireless Tab Instant Wireless Series Appendix a Troubleshooting Frequently Asked QuestionsDoes the Access Point function as a firewall? Appendix B Setting Up the TCP/IP and IPX Protocols Setting Up TCP/IP in WindowsTCP/IP Setup for Windows 98 and Millennium IPX Setup for Windows 98 and MillenniumTCP/IP Setup for Windows NT IPX Setup for Windows NTTCP/IP Setup for Windows XP TCP/IP Setup for WindowsIPX Setup for Windows Appendix C Glossary Instant Wireless Series Instant Wireless Series Instant Wireless Series Appendix D Specifications EnvironmentalCopyright 2003 Linksys, All Rights Reserved

WAP54G specifications

The D-Link WAP54G is a wireless access point that offers a variety of features aimed at enhancing network connectivity and performance. Designed for small to medium-sized environments, this device is an essential component for creating a reliable wireless network. With its impressive capabilities, the WAP54G easily integrates into existing networks, providing enhanced coverage and flexibility.

One of the main features of the WAP54G is its support for the IEEE 802.11g standard, which allows for data transfer rates of up to 54 Mbps. This standard is backward compatible with 802.11b devices, ensuring that users can maintain connectivity with older hardware. This level of compatibility makes the WAP54G a versatile choice for diverse networking needs.

The device is equipped with advanced security features, including WPA and WPA2 encryption protocols, ensuring that users can protect their network from unauthorized access. These security measures are essential in today’s world, where data breaches are increasingly common. Additionally, the WAP54G supports MAC address filtering, which further restricts access to only authorized devices.

For connectivity, the WAP54G includes multiple Ethernet ports, allowing it to be connected directly to a wired network. This feature enables the access point to bridge the gap between wired and wireless devices, facilitating seamless communication. Moreover, the WAP54G supports Power over Ethernet (PoE), which simplifies installation by allowing it to receive power and data through a single Ethernet cable. This is particularly beneficial in environments where power outlets are limited or difficult to access.

Another noteworthy aspect of the WAP54G is its coverage capabilities. With its adjustable antennas, users can optimize signal distribution throughout a building, overcoming common obstacles such as walls and furniture that can hinder wireless performance. The access point also boasts a user-friendly web-based interface, making it easy to configure and manage settings for both novice and experienced users alike.

In terms of reliability, the D-Link WAP54G features a solid build quality and a compact design, allowing it to fit seamlessly into various environments. The device is also equipped with LED indicators that provide real-time status updates on power, Ethernet connection, and wireless activity, enabling users to monitor their network easily.

Overall, the D-Link WAP54G is a robust wireless access point that combines speed, security, and flexibility, making it an excellent choice for enhancing network performance in both home and office settings.
Top Page Image Contents