D-Link DSL-564T manual Remote Log menu

Page 65

DSL-564T ADSL Router User’s Guide

Remote Log

Us the Remote Log menu to set up logging to servers or computers that are located outside the LAN or subnet of the Router.

Figure 4-16. Remote Log menu

Select the Log Level from the pull-down menu. The levels available are: Alert, Critical, Debug, Error, Info, Notice, Panic and Warning. Type in the IP address of a receiver for the log message in the Add an IP Address field and click on the Add button. Log message receivers that are added appear listed in the Select a logging destination pull-down menu. These may be used at any time for other types of log messages. To remove a log message receiver from the list, select it and click on the Remove button. Click the Apply button when you have configured the log message receivers. Remember to save the settings to non-volatile memory.

53

Image 65
Contents DSL-564T Adsl Router User’s Guide FCC Warning DSL-564T DSL Router User’s GuideWarranties Exclusive Wichtige SicherheitshinweiseSoftware HardwareWarranty and Registration Information for USA Only DSL-564T DSL Router User’s Guide Table of Contents Status Menus Before You Start Installation RequirementsAbout This User’s Guide About Clip Connections RFC Ethernet Port NIC AdapterAdditional Software Information you will need from your Adsl service provider Information you will need about your LAN or computer Router Description and Operation What is ADSL?Router Features Standards Compatibility and Compliance Packing List Front Panel DisplayRear Panel Connections Factory Reset Button Power on RouterNetwork Connections Hub or Switch to Router ConnectionConnect Adsl Line Connect Router to EthernetComputer to Router Connection Wan Configuration Summary Configuring IP Settings on Your ComputerConfigure Windows XP for Dhcp DSL-564T Adsl Router User’s Guide Windows Configure Windows 2000 for DhcpWindows 95 and Windows Configure Windows ME for DhcpWindows ME Windows NT 4.0 Workstations Configure Windows 95 and Windows 98 for DhcpConfigure Windows NT 4.0 for Dhcp Login to Home Access the Configuration ManagerHome Status Information window Configure the RouterOpening Setup window Setup MenuDSL Modulation Settings Configure Connection 1 for PPPoAPPPoA Connection 1 Setup menu Change the Connection Type Configure Connection 1 for PPPoESetup Configure Connection 1 for PPPoE Setup Configure Connection 1 for Bridge Configure Connection 1 for BridgeSetup Configure Connection 1 for Static IP for the WAN Configure Connection 1 for Static IP for WANDSL-564T Adsl Router User’s Guide Setup Configure Connection 1 for Dhcp service for the WAN Configure Connection 1 for Dhcp for WAN10. Setup Configure Connection 1 for Clip IPoA Configure Connection 1 for ClipCreate a New Connection New Connection Example 1 Create a New PPPoE Connection 11. Setup a New Connection ConnectionNew Connection Example 2 Create a New Bridge Connection 12. Setup a New Connection ConnectionDhcp Parameter Description Start IP Dhcp Configuration for LANEnd IP Lease Time14. Configure Dhcp Relay Service Enable Dhcp RelayManagement IP 15. Configure Management IP16. Router Tools Menus Save Configuration Changes18. Changes permanently saved message Advanced Router Management Advanced UPnP window UPnPLAN Clients LAN Clients SetupAdvanced Port Forwarding window Port ForwardingAudio/Video Category Available Rules GamesApplications ServersSet up Custom Port Forwarding Rules Port Forwarding User Rules Management Access Control menu Access ControlVPN Advanced Security Enable/Disable NAT and FirewallDMZ IP Address Setup Remote ManagementBridge Filters 10. Multicast pass-through menu Multicast Pass-through11. Static Routing menu Static Routing12. Dynamic Routing RIP menu Dynamic RoutingMultiple Virtual Connections 13. Tools and utility menu links Tools and Utility Menus14. User Management menu User Management15. Tools System Commands menu System Commands16. Remote Log menu Remote Log17. Tools Update Gateway window Update Gateway18. Tools Ping Test window Ping Test19. Tools Modem Test window Modem Test20. Status display links Status Menus21. Network Statistics window Network StatisticsDhcp Clients Connection StatusProduct Information Modem StatusHelp Menu System LogProtocols StandardsData Transfer RateCE Class B, FCC Class B Part Physical and EnvironmentalManual IP Address Assignment Using the Default IP AddressAssigning Network IP Addresses Changing the IP Address of the Router Using DhcpIP Setup Example #2 IP Addresses IP ConceptsClass Beginning Address Ending Address IP Network ClassesIP Class Subnet Mask Subnet MaskMicrofilters Microfilter InstallationLine Splitter Line Splitter InstallationEast Chang An Ave., Dong Cheng District TEL 27-12-665-2165 FAX 2F, No , Pao-chung Road, Hsin-tien, Taipei, Taiwan Registration Card