Linksys WRT54GL (EU/LA) manual Windows 98SE or Me Instructions, Windows 2000 or XP Instructions

Page 88

Wireless-G Broadband Router

Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter

This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features. Follow the steps in this appendix to find the adapter’s MAC or IP address in Windows 98, Me, 2000, or XP.

Windows 98SE or Me Instructions

1.Click Start and Run. In the Open field, enter winipcfg. Then press the Enter key or the OK button.

2.When the IP Configuration screen appears, select the Ethernet adapter you have connected to the Router via a CAT 5 Ethernet network cable. See Figure E-1.

3.Write down the Adapter Address as shown on your computer screen (see Figure E-2). This is the MAC address for your Ethernet adapter and is shown as a series of numbers and letters.

The MAC address/Adapter Address is what you will use for MAC address cloning or MAC filtering.

The example in Figure E-3 shows the Ethernet adapter’s IP address as 192.168.1.100. Your computer may show something different.

Note: The MAC address is also called the Adapter Address.

Figure E-1: IP Configuration Screen

Figure E-2: MAC Address/Adapter Address

Windows 2000 or XP Instructions

1.Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button.

2.At the command prompt, enter ipconfig /all. Then press the Enter key.

Figure E-3: MAC Address/Physical Address

Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter

80

Windows 98SE or Me Instructions

Image 88

Contents Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel23 Setup Wizard’s Configure Wireless Settings Screen 19 Wireless Tab Wireless Security WPA2 Personal Figure E-5 MAC Address Clone Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Broadband Router Back PanelFront Panel Cisco logoConnecting the Wireless-G Broadband Router OverviewConnecting Your Network Devices Hardware Installation for Connection to Another Router Connecting Another RouterConnecting Your Network Devices Setting up the Wireless-G Broadband Router Using the Setup WizardSetup Wizard’s Disconnect the Modem from PC Screen Setup Wizard’s Connect a Network Cable to a PC Screen Setup Wizard’s Power on the Router Screen Setup Wizard’s Check the Router’s Status Screen Cable or DhcpDSL PPPoE Static IPPptp L2TP 16 Setup Wizard’s Advanced Internet Settings Telstra Screen Telstra18 Setup Wizard’s Configure Wireless Settings Screen Using the Router’s SecureEasySetup Feature 19 Setup Wizard’s SecureEasySetup Screen24 Setup Wizard’s Confirm New Settings Screen 26 Setup Wizard’s Congratulations Screen Manually Configuring the Router’s Wireless Settings 27 Setup Wizard’s Configure Wireless Settings ScreenWPA-PSK WEP 64-Bit WEP 128-Bit33 Setup Wizard’s Congratulations Screen Using SecureEasySetup to Configure Your Notebook 34 Setup Wizard’s Welcome Start Wizard Screen37 Configure Wireless Settings #2 Screen 38 Your Wireless Settings Screen Configuring the Wireless-G Broadband Router Setup Tab Basic Setup Internet SetupPPPoE Connection Type Optional Settings Router IP Setup Tab Ddns 12 Setup Tab DdnsSetup Tab MAC Address Clone 13 Setup Tab MAC Address CloneSetup Tab Advanced Routing 14 Setup Tab Advanced Routing GatewayWireless Tab Basic Wireless Settings Wireless Tab Wireless Security 17 Wireless Tab Wireless Security WPA Personal20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter 23 Wireless Tab Wireless MAC FilterWireless Tab Advanced Wireless Settings SettingWireless-G Broadband Router Security Tab Firewall Security Tab VPN PassthroughAccess Restrictions Tab Internet Access To create an Internet Access policy31 Port Services To create an Inbound Traffic policyApplications and Gaming Tab Port Range Forward 33 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Triggering Port TriggeringApplications and Gaming Tab DMZ Applications and Gaming Tab QoSDevice Priority Ethernet Port PriorityApplication Port Priority Administration Tab Management Administration Tab LogAdministration Tab Diagnostics 39 Administration Tab DiagnosticsAdministration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management Status Tab Router 45 Status Tab RouterStatus Tab Local Network 46 Status Tab Local NetworkStatus Tab Wireless 48 Status Tab WirelessCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Broadband Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?What is the Ieee 802.11g standard? Is the Router cross-platform compatible?What is the Ieee 802.11b standard? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is ad-hoc mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP? What is a MAC Address?How do I reset the Router? How do I resolve issues with signal loss?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Appendix G Specifications StandardsStorage Temp 4ºF to 158ºF Operating Humidity Storage HumidityAppendix H Warranty Information Radio EN 300 EMC EN 301 489-1, EN 301 Safety EN Appendix I Regulatory InformationBelgium Applicable Power Levels in France Open the Wireless Network Connection window FCC Statement Europe Mail Address Appendix J Contact InformationOutside of Europe Mail Address Asia Pacific