Linksys WRT54GL (EU/LA) manual Wireless-G Broadband Router

Page 54

Wireless-G Broadband Router

Fragmentation Threshold. This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of 2347.

AP Isolation. This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. To use this function, select On. AP Isolation is Off by default.

Secure Easy Setup. This feature allows you to enable or disable the SecureEasySetup feature. Select Disable to disable the feature and turn off the button’s light. The feature is enabled by default.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Chapter 6: Configuring the Wireless-G Broadband Router

46

The Wireless Tab - Advanced Wireless Settings

Image 54

Contents Wireless- G How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a TroubleshootingAppendix B Wireless Security Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel23 Setup Wizard’s Configure Wireless Settings Screen 19 Wireless Tab Wireless Security WPA2 Personal Figure E-5 MAC Address Clone Introduction WelcomeWhat’s in this User Guide? Wireless-G Broadband Router Ssid service set identifier your wireless network’s name Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Broadband Router Back PanelFront Panel Cisco logoConnecting the Wireless-G Broadband Router OverviewConnecting Your Network Devices Hardware Installation for Connection to Another Router Connecting Another RouterConnecting Your Network Devices Setting up the Wireless-G Broadband Router Using the Setup WizardSetup Wizard’s Disconnect the Modem from PC Screen Setup Wizard’s Connect a Network Cable to a PC Screen Setup Wizard’s Power on the Router Screen Setup Wizard’s Check the Router’s Status Screen Cable or DhcpDSL PPPoE Static IPPptp L2TP 16 Setup Wizard’s Advanced Internet Settings Telstra Screen Telstra18 Setup Wizard’s Configure Wireless Settings Screen Using the Router’s SecureEasySetup Feature 19 Setup Wizard’s SecureEasySetup Screen24 Setup Wizard’s Confirm New Settings Screen 26 Setup Wizard’s Congratulations Screen Manually Configuring the Router’s Wireless Settings 27 Setup Wizard’s Configure Wireless Settings ScreenWPA-PSK WEP 64-Bit WEP 128-Bit33 Setup Wizard’s Congratulations Screen Using SecureEasySetup to Configure Your Notebook 34 Setup Wizard’s Welcome Start Wizard Screen37 Configure Wireless Settings #2 Screen 38 Your Wireless Settings Screen Configuring the Wireless-G Broadband Router Setup Tab Basic Setup Internet SetupPPPoE Connection Type Optional Settings Router IP Setup Tab Ddns 12 Setup Tab DdnsSetup Tab MAC Address Clone 13 Setup Tab MAC Address CloneSetup Tab Advanced Routing 14 Setup Tab Advanced Routing GatewayWireless Tab Basic Wireless Settings Wireless Tab Wireless Security 17 Wireless Tab Wireless Security WPA Personal20 Wireless Tab Wireless Security WPA2 Enterprise 21 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter 23 Wireless Tab Wireless MAC FilterWireless Tab Advanced Wireless Settings SettingWireless-G Broadband Router Security Tab Firewall Security Tab VPN PassthroughAccess Restrictions Tab Internet Access To create an Internet Access policy31 Port Services To create an Inbound Traffic policyApplications and Gaming Tab Port Range Forward 33 Applications and Gaming Tab Port Range ForwardApplications & Gaming Tab Port Triggering Port TriggeringDevice Priority Applications and Gaming Tab DMZApplications and Gaming Tab QoS Ethernet Port PriorityApplication Port Priority Administration Tab Management Administration Tab LogAdministration Tab Diagnostics 39 Administration Tab DiagnosticsAdministration Tab Factory Defaults Administration Tab Firmware UpgradeAdministration Tab Config Management Status Tab Router 45 Status Tab RouterStatus Tab Local Network 46 Status Tab Local NetworkStatus Tab Wireless 48 Status Tab WirelessAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G Broadband Router Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Broadband Router Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is the Ieee 802.11g standard? What is DMZ Hosting?What are the advanced features of the Router? Is the Router cross-platform compatible?What Ieee 802.11b features are supported? What is the Ieee 802.11b standard?What Ieee 802.11g features are supported? What is ad-hoc mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? How do I reset the Router? What is WEP?What is a MAC Address? How do I resolve issues with signal loss?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router Appendix C Upgrading Firmware Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Wireless-G Broadband Router Appendix G Specifications StandardsStorage Temp 4ºF to 158ºF Operating Humidity Storage HumidityAppendix H Warranty Information Radio EN 300 EMC EN 301 489-1, EN 301 Safety EN Appendix I Regulatory InformationBelgium Applicable Power Levels in France Open the Wireless Network Connection window FCC Statement Appendix J Contact Information Europe Mail AddressOutside of Europe Mail Address Asia Pacific