Linksys WRT54GX manual Wireless Tab Wireless MAC Filter

Page 27

Wireless-G Broadband Router with SRX

The Wireless Tab - Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.

Wireless MAC Filter. To filter wireless users by MAC Address, either permitting or blocking access, click Enable.

If you do not wish to filter users by MAC Address, select Disable.

Prevent. Clicking this button will block wireless access by MAC Address.

Permit Only. Clicking this button will allow wireless access by MAC Address.

There are 50 fields provided in which you can list users, by MAC Address, whose access you wish to provide or block. Just enter the MAC Address for the PC whose access you want to filter in one of the fields .For a more convenient way to add MAC addresses, click the Select MAC Address From Networked Computers button. The Networked Computers screen will appear. Select the MAC Addresses you want. Then click the Select button. Click the Refresh button if you want to refresh the screen. Click the Close button to return to the previous screen.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

Figure 5-20: Wireless Tab - Wireless MAC Filter

Figure 5-21: Wireless Tab - Wireless MAC Filter - Networked

Computers

Chapter 5: Configuring the Wireless-G Broadband Router

21

The Wireless Tab - Wireless MAC Filter

Image 27

Contents 802 GHz .11g Wireless- G How to Use This User Guide Copyright and TrademarksWord definition Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Router’s Back Panel Router’s Reset Button27 Port Services Welcome IntroductionWhat’s in this Guide? Wireless-G Broadband Router with SRX Network Layout Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterPassword Screen Configuring the Wireless-G Broadband RouterInternet Setup Setup Tab Basic SetupStatic IP Connection Type Pptp Connection Type Packet a unit of data sent over a network Network SetupNetwork Address Server Settings Dhcp 12 Setup Tab Ddns Setup Tab Ddns13 Setup Tab MAC Address Clone Setup Tab MAC Address Clone14 Setup Tab Advanced Routing Setup Tab Advanced Routing16 Wireless Tab Basic Wireless Settings Wireless Tab Basic Wireless SettingsWPA Radius Wireless Tab Wireless SecurityWEP 20 Wireless Tab Wireless MAC Filter Wireless Tab Wireless MAC Filter22 Wireless Tab Advanced Wireless Settings Wireless Tab Advanced Wireless Settings23 Security Tab Firewall Security Tab FirewallTo create an Internet Access policy Access Restrictions Tab Internet AccessUrl the address of a file located on the Internet Ftp a protocol used to transfer files over a TCP/IP networkApplications and Gaming Tab Port Triggering Applications and Gaming Tab Port Range ForwardApplications and Gaming Tab DMZ Applications and Gaming Tab UPnP ForwardingUPnP Forwarding Snmp Administration Tab ManagementAdministration Tab Log Administration Tab DiagnosticsUPnP Administration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management Status Tab RouterIsp your internet provider 39 Status Tab Local Network Status Tab Local NetworkEncryption encoding data transmitted in a network Status Tab WirelessSystem Performance Status Tab System PerformanceWireless-G Broadband Router with SRX Appendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC For Windows 98SE, Me, 2000, and XP Open a command prompt. For Windows 98SE and Me TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with SRX Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultMy power LED will not stop flashing Need to upgrade the firmwareCannot connect to the Internet How do I turn on SRX on my router? My wireless-G speed seems to be slowDoes the Router support IPX or AppleTalk? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?What are the advanced features of the Router? Will the Router function in a Macintosh environment?What is infrastructure mode? What is the Ieee 802.11g standard?What Ieee 802.11b features are supported? What is ad-hoc mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? How do I resolve issues with signal loss? What is WEP?What is a MAC Address? How do I reset the Router?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router with SRX Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareAppendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Figure E-1 IP Configuration ScreenFor the Router’s Web-based Utility Windows 2000 or XP InstructionsAppendix F Glossary Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Appendix G Specifications ModelStandards Storage Temp Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationFrance Appendix J Contact Information