Linksys WRT54GX manual Network Setup, Packet a unit of data sent over a network

Page 19

Wireless-G Broadband Router with SRX

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Router Name. In this field, you can type a name of up to 39 characters to represent the Router.

Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. The default setting, Manual, allows you to enter the largest packet size that will be transmitted. The recommended size, entered in the Size field, is 1492. You should leave this value in the 1200 to 1500 range. To have the Router select the best MTU for your Internet connection, select Auto.

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless Setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Chapter 5: Configuring the Wireless-G Broadband Router

Figure 5-8: Optional Settings

packet: a unit of data sent over a network

Figure 5-9: Router IP

13

The Setup Tab - Basic Setup

Image 19
Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Appendix B Wireless Security Appendix a TroubleshootingCommon Problems and Solutions Frequently Asked Questions Router’s Back Panel Router’s Reset Button27 Port Services Welcome IntroductionWhat’s in this Guide? Wireless-G Broadband Router with SRX Network Layout Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Network TopologyPlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterPassword Screen Configuring the Wireless-G Broadband RouterInternet Setup Setup Tab Basic SetupStatic IP Connection Type Pptp Connection Type Packet a unit of data sent over a network Network SetupNetwork Address Server Settings Dhcp 12 Setup Tab Ddns Setup Tab Ddns13 Setup Tab MAC Address Clone Setup Tab MAC Address Clone14 Setup Tab Advanced Routing Setup Tab Advanced Routing16 Wireless Tab Basic Wireless Settings Wireless Tab Basic Wireless SettingsWPA Radius Wireless Tab Wireless SecurityWEP 20 Wireless Tab Wireless MAC Filter Wireless Tab Wireless MAC Filter22 Wireless Tab Advanced Wireless Settings Wireless Tab Advanced Wireless Settings23 Security Tab Firewall Security Tab FirewallTo create an Internet Access policy Access Restrictions Tab Internet AccessUrl the address of a file located on the Internet Ftp a protocol used to transfer files over a TCP/IP networkApplications and Gaming Tab Port Triggering Applications and Gaming Tab Port Range ForwardApplications and Gaming Tab UPnP Forwarding Applications and Gaming Tab DMZUPnP Forwarding Snmp Administration Tab ManagementAdministration Tab Diagnostics Administration Tab LogUPnP Administration Tab Firmware Upgrade Administration Tab Factory DefaultsStatus Tab Router Administration Tab Config ManagementIsp your internet provider 39 Status Tab Local Network Status Tab Local NetworkEncryption encoding data transmitted in a network Status Tab WirelessSystem Performance Status Tab System PerformanceWireless-G Broadband Router with SRX Common Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC For Windows 98SE, Me, 2000, and XP Open a command prompt. For Windows 98SE and Me TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Wireless-G Broadband Router with SRX Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultMy power LED will not stop flashing Need to upgrade the firmwareCannot connect to the Internet How do I turn on SRX on my router? My wireless-G speed seems to be slowDoes the Router support IPX or AppleTalk? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?What are the advanced features of the Router? Will the Router function in a Macintosh environment?What is infrastructure mode? What is the Ieee 802.11g standard?What Ieee 802.11b features are supported? What is ad-hoc mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? How do I resolve issues with signal loss? What is WEP?What is a MAC Address? How do I reset the Router?Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Broadband Router with SRX Appendix C Upgrading Firmware Figure C-1 Upgrade FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Figure E-1 IP Configuration ScreenFor the Router’s Web-based Utility Windows 2000 or XP InstructionsAppendix F Glossary Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Wireless-G Broadband Router with SRX Model Appendix G SpecificationsStandards Storage Temp Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationFrance Appendix J Contact Information