Actiontec electronic Wireless-Ready user manual Security Alarm System

Page 50

Appendix A Reference

easiest way to do this is to purchase a pair of two-line modular adapters, a line- cord coupler, and some short lengths of phone cable, available at any telephone supply retailer.

Note: Do not purchase a 1-line modular adapter or line splitter. Installing either of these items results in two phone jacks on Line 1, and no access to Line 2.

1.Disconnect the telephone from the two-line phone jack.

2.Install one of the two-line modular adapters (modular adapter #1) in the phone jack

3.If Qwest DSL is on Line 1, install the phone filter in the Line 1 jack of modu- lar adapter #1.

4.Install a short length of phone cable between the phone filter and the Line 1 jack of the other two-line modular adapter (modular adapter #2).

5.Install a short length of phone cable between the Line 2 jacks of modular adapters #1 and #2.

6.Connect the line-cord coupler to 2-line modular adapter #2.

7.Install a short length of phone cable between the line-cord coupler and the telephone.

If Qwest DSL is on Line 2, use the same procedure, but install the phone filter on Line 2.

Security Alarm System

If the user plans to connect Qwest DSL at a location that has two phone lines, Qwest DSL must be installed on the phone line that does not service the alarm system.

If the alarm system and Qwest DSL must share the same phone line, contact Qwest Sales to order a technical install. Special wiring needs are required when Qwest DSL and the alarm system share the same phone line. Qwest Sales telephone num- bers are listed at the back of this manual.

47

Image 50
Contents Wireless-Ready DSL Gateway Table of Contents Computer Security Minimum System Requirements Package ContentsIntroduction1 Technical Support Actiontec Electronics, IncConnecting Gateway Connecting the Power and DSL CableActiontec Wireless-Ready DSL Gateway Connecting to a Computer EthernetUSB Connecting the Phone Filters Connecting Network Computers Wireless Actiontec Wireless-Ready DSL Gateway Configuring Gateway Actiontec Wireless-Ready DSL Gateway Configuring the Gateway Actiontec Wireless-Ready DSL Gateway Disconnecting from the Internet Using Qwest DSLConnecting to the Internet Actiontec Wireless-Ready DSL Gateway Basic Setup Actiontec Wireless-Ready DSL Gateway Gateway Features Actiontec Wireless-Ready DSL Gateway Basic Setup Actiontec Wireless-Ready DSL Gateway Advanced Setup Accessing Advanced SetupWAN IP Address Obtain an IP Address through PPPoE or PPPoA Obtain an IP Through Dhcp Specify a Static IP AddressChannel Wireless SettingsWireless Equivalent Privacy Off LAN IP Address Dhcp Server Configuration Dhcp ServerServices Blocking Website Blocking VPN Pass ThroughRemote Management Port Forwarding DMZ HostingMAC Address Cloning StatusActiontec Wireless-Ready DSL Gateway Utilities7 Web Activity LogUpgrade Firmware DSL SettingsRestore Default Settings Utilities Actiontec Wireless-Ready DSL Gateway Troubleshooting LAN Connection FailureTime out error occurs when entering a URL or IP Address Reference Locating Computer InformationWindows Me Locating Windows Operating System FilesWindows 98, 98 SE Windows NT Wiring Information Two-Line PhoneSecurity Alarm System Automatic Water Meter PBX or Key SystemComputer Security Anti-Virus Programs Internet Browsers Actiontec Wireless-Ready DSL Gateway Specifications C GeneralWireless Operating Range LED IndicatorsEnvironmental Actiontec Wireless-Ready DSL Gateway Glossary Firewall ISP Internet Service ProviderMAC Media Access Control Address GatewaySubnet Mask Weca Wireless Ethernet Compatibility AllianceWlan Wireless Local Area Network TCP/IP Transmission Control Protocol/Internet ProtocolActiontec Wireless-Ready DSL Gateway Class B Equipment Regulatory Compliance NoticesModifications Actiontec Wireless-Ready DSL Gateway Limited Warranty Actiontec Electronics, Inc North Mary Avenue Sunnyvale, CA Limited Warranty