AMD TPC-660G manual

Page 6

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to the user's manual.

e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW - 20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-

AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16.CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORD-

ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.

TPC-660G User Manual

vi

Image 6
Contents TPC-660G Copyright Acknowledgements This Manual Covers the Following ModelsProduct Warranty 1 year FCC Class a Technical Support and Assistance Safety Instructions Packing ListPage Contents Chapter Features in Windows XP Embedded Appendix F Fuse Specifications Page General Information Fanless Powerful Communication CapabilityIntroduction Bright DisplaySpecifications SafetyEnvironment Operating Temperature 0 ~ 50 C 32 ~ 122 F Power LCD SpecificationsTouchscreen Specifications Backlight 1 Ccfl Backlight Life Time 20,000 hoursI/O Ports Arrangement Panel MountingExploded Diagram Panel MountingDimensions and Cutout Dimensions & CutoutPage System Setup Unpack the Package Power Connector and Power Lines Plugging in the Power Line Bootup Screen Page System Engine Mainboard Connectors & Jumper Settings Main Board Connectors Page Software Configuration VGA Driver Installation Device ManagerUpdate Driver Update Wizard-2 Update Wizard-4 Update Wizard-6 Entertainment Encryption/Decryption Driver 10 Device Manager12 Install Wizard 14 Driver Installation Complete Page Features Windows XP Embedded Features in Windows XP Embedded EWFHorm Advantech UtilitiesVersion Information Serial Port Settings Appendix a Serial Port Settings Jumper SettingData Format Control Setting SW2 Baud Rate Setting SW3 Watchdog Timer Programming Appendix B Watchdog Timer Programming OverviewWatchdog Timer Programming Figure B.1 Watchdog Timer ProgrammingTable B.1 Watchdog Timer Registers Enable watchdog timer and set 10 sec. as timeout interval Example ProgramsEnable watchdog timer and set 5 minutes as timeout interval Enable watchdog timer to be reset by mouse Enable watchdog timer to be reset by keyboard Generate a time-out signal without timer counting Page Watchdog Timer Programming on WinCE Appendix C Watchdog Timer Program- ming on WinCE DeviceIOControlLpvoid lpOutBuffer Parameters How to Use the Control Code Ioctl WdtenableIoctlwdtgettimeout CTLCODEFILEDEVICEUNKNOWN,ID, METHODBUFFERED, Fileanyaccess ExamplesAppendixC Page Accessory Kit Assembly Procedure Appendix D Accessory Kit Assembly Procedure CompactFlash to IDE Transfer KitFigure D.3 CompactFlash Slot Figure D.6 Connect the CD-ROM via the IDE Cable Touchscreen Installation Configuration Appendix E Touchscreen Installation & Configuration Driver InstallationFigure E.3 Install Wizard Uninstall the Driver Figure E.5 UninstallTouchscreen Calibration CalibrateFigure E.8 Standard Calibration Figure E.10 Advanced Calibration Figure E.11 Advanced Calibration Draw Figure E.13 DrawFigure E.14 Clear Screen OptionFuse Specifications Appendix F Fuse Specifications Fuse SpecificationsFuse Replacement