Sony Digital Studio System manual Safety Information and Caution

Page 3

Safety Information and Caution

Your computer’s installed optical drives may vary, depending on the system configuration you have purchased. See the Specifications sheet for details on your installed optical drives.

DVD-RW Laser Diode Properties

Laser Output

1.3 mW

 

(CD-Read)

 

1.1 mW

 

(DVD-Read)

 

42.3 mW

 

(DVD-Write)

 

21.9 mW

 

(CD-Write)

Wave Length

650-662 nm

 

(DVD)

 

773-797 nm

 

(CD)

 

 

DVD-ROM Laser Diode Properties

Laser Output

0.55 mW (DVD)

 

0.39 mW (CD)

Wave Length

635-665 nm

 

(DVD)

 

770-810 nm

 

(CD)

 

 

CD-RW Laser Diode Properties

Laser Output

2.0 mW (Read)

 

53.0 mW (Write)

Wave Length

778-790 nm

 

 

CD-ROM Laser Diode Properties

Laser Output

0.2 mW

Wave Length

760-810 nm

 

 

iii

To prevent fire or shock hazard, do not expose your desktop to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Never install modem or telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wire or terminals unless the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Avoid using the modem during an electrical storm.

Do not use the modem or a telephone to report a gas leak in the vicinity of the leak.

The socket outlet shall be installed near the equipment and shall be easily accessible.

!To change the backup battery, please contact your nearest Sony Service Center.

!Caution: The use of optical instruments with this product will increase eye hazard. As the laser beam used in this product is harmful to the eyes, do not attempt to disassemble the drive cabinet. Refer servicing to qualified personnel only.

!Danger: Visible and invisible laser radiation when open. Avoid direct exposure to beam.

!For CD-RW: Danger—Visible and invisible laser radiation when open. Avoid direct exposure to beam.

!For DVD-RW: Danger—Visible laser radiation when open. Avoid direct exposure to beam.

Image 3
Contents Page Vaio Digital Studio System Reference Manual Owner’s RecordSafety Information and Caution Vaio Digital Studio System Reference Manual Regulatory Information Telephone Consumer Protection Act United States Disposal of Lithium Battery Industry Canada Notice Contents System Board Index Xii Chapter Identifying Components Front View Drive Description DrivesButton or switch Description Buttons and SwitchesIndicator Description IndicatorsConnector Description ConnectorsUSB3, USB4 Rear ViewIconDescription IconsOn models equipped with Giga Pocket features Keyboard and Mouse Ports USB PortsEthernet Port Serial Port Printer/Parallel PortVGA Monitor Port Telephone and Line Jacks Link Ieee 1394 Ports Expansion Slots Chapter Configuring Your System Accessing the Bios Setup Utility Changing the Displays Power Management Settings Vaio Digital Studio System Reference Manual Click the Advanced tab Select the desired settings Vaio Digital Studio System Reference Manual Configuring Your System Vaio Digital Studio System Reference Manual Chapter Removing, Installing, Replacing Components Removing the Side Cover Replacing the Side Cover Removing a PCI Add-in Card Removing, Installing, and Replacing Components Installing a PCI Add-In Card Removing, Installing, and Replacing Components Replacing the Lithium Battery Push in not down to pop out battery Vaio Digital Studio System Reference Manual Removing a Memory Module Memory module configurations MB Installing System MemoryRemove the AGP add-in card Latch Edge Connector Removing a Slot Cover Covering an Open I/O Slot Installing a 3.5-inch Internal Hard Disk Drive Disconnect the drive connector a in diagram Removing, Installing, and Replacing Components Drive connectors Power connectors Tab Disk drive holder To identify additional hard disk space Removing the Power Supply Replacing the Power Supply Vaio Digital Studio System Reference Manual Chapter System Board Memory Module DDR-DIMM Slots Pin Signal Name Power Supply and Aux Power HeadersPin Jumper Plug Position Function CLR Cmos JumperVaio Digital Studio System Reference Manual Chapter Cmos Setup Options Vaio Digital Studio System Reference Manual Main Screen CD-ROM Advanced Screen 2F8H/IRQ3 Power Screen Atapi MO Boot ScreenExit Screen Vaio Digital Studio System Reference Manual Chapter Miscellaneous Technical Information If you set these passwords Following passwords are required User and Supervisor PasswordsBeep Code Error Messages Message Meaning PCI Configuration Status and Error MessagesMiscellaneous Technical Information DMA Channel Assignments DMA Default Channel AssignmentAddress Range hex Description System I/O Address MapAddresses that may be used by add-in cards are not listed Memory Map Address range Default configurationIRQ IRQ SettingsAGP Bus Chapter SpecificationsProcessors ChipsetL2 Cache Memory ConfigurationsPCI Bus Memory ModulesAudio CommunicationsGiga Pocket I/O Optical Drives Expansion SlotsFloppy Disk Drive and Controller Hard Drives and ControllersROM System BiosVaio Digital Studio System Reference Manual Index Vaio Digital Studio System Reference Manual Index Vaio Digital Studio System Reference Manual