C H A P T E R 2
Hardware Modifications
| Figure | Bracket for the hard disk drive |
|
|
| ||
|
|
| 2.874" |
|
|
|
|
0.188" |
|
| (73.00mm) |
|
|
|
|
|
| 0 0.125" | 1 | 2x 0.079" |
| ||
(4.795±0.125mm) |
| 2 | C | (2.00mm) |
| ||
|
| (3.200mm) |
| ||||
|
|
| L |
|
|
| |
|
|
|
|
|
| 0.299" | (8.60) |
|
|
|
|
|
| (7.60mm) | |
0.125" | 0.082" | 2x R full | 4x R |
|
|
| |
(3.20mm) | (2.10mm) |
|
| 0.039" | 2x R 0.059" | 3x R 1.00 | |
(1.60mm) | 0.165" |
|
| (1.00mm) | (1.50mm) | (7.80) | |
(4.20mm) |
|
| 0.549" |
|
|
| |
|
| 1.5" |
|
|
| ||
|
|
| (13.95mm) |
|
|
| |
|
|
| (38.10mm) |
|
|
| |
|
|
|
|
|
|
| |
0.192" |
| 3 |
|
|
|
| |
|
|
|
|
|
| ||
(4.900±0.125mm) |
|
|
|
|
|
| |
3x 0.307" |
|
|
|
|
|
|
|
(7.80mm) |
| 3x 0.137" |
|
|
|
|
|
|
| 3x 0 0.118" |
|
|
| ||
|
| (3.50mm) |
|
|
| ||
|
| (3.00mm) |
|
|
| ||
|
| 3x 0.275" | 6x R 0.059" |
| |||
|
|
| 1.299" |
| |||
|
| (7.00mm) |
| (1.50mm) |
| ||
0.137" |
|
| (33.00mm) |
|
|
| |
|
| 2.598" |
|
|
|
| |
(3.50mm) |
|
| (66.00mm) |
|
| Key |
|
|
|
|
|
|
|
| |
|
|
|
|
| 1 | This surface to be free of burrs | |
|
|
|
|
|
| and sharp edges. | |
|
|
|
|
| 2 | Mark part number, rev level, | |
|
|
|
|
|
| vendor I.D., and date code | |
|
|
|
|
|
| with 0.19±0.06 high | |
Notes: |
|
|
|
|
| permanent contrasting | |
|
|
|
|
| characters. |
| |
|
|
|
|
|
| Locate where shown. | |
1.Interpret dimensions and tolerances per
ANSI | 3 Arrow indicates direction of |
| material grain. |
2.Material: CRS
3.Finish: Zinc
4.Maximum burr allowance is 15% of material thickness.
5.Tooling required to make this part to be property of Apple Computer, Inc. and shall be permanently marked with Apple’s name and appropriate part number.
6.All dimensions apply after finish.
10 | 200 MB Hard Disk Drive |