AudioQuest M-27 specifications Connections to Printer, Sample Printouts

Page 13

Parallel Printers

printer. Check printer manual to set up printer. If switches are changed it may be necessary to reset the Check interconnecting cable to assure it is the proper cable.

Set the internal switches in the M-27 to agree with the printer. It is not necessary to reset the M-27 if switches are changed.

Connections to Printer

1.Make sure printer is set up to agree with M-27.

2.Connect printer cable to printer.

3.Turn on printer.

5.Connect printer cable to M-27. Cable goes toward top of M-27 with red strip in middle of unit.

After data is accumulated, a printer is connected to the M-27 and the stored data is printed (see Figure 9). The printer may be used while the M-27 is still gathering data to obtain intermediate results. No data is lost in either unit until the unit is reset.

All the data may be printed, or only selected data if desired. It is possible to change the printout in the middle to obtain, for instance, a 10-minute histogram for part of the time and a 1-minute histogram for another.

The M-27 remembers previous PRINT keystrokes and will print only that data unless the keystroke has been cleared.

Sample Printouts

Heading

A heading is printed when PRINT is pressed. It allows the user to write in identification data (see Figure 10).

Summary

The summary data includes parameter data of how the M-27 is set up and a summary of all the M- 27 functions (see Figure 11).

Events

The event data is printed for events with data. It includes start time, run time, peak and max levels as well as accumulated data for all three dosimeters (see Figure 12).

Histograms

Three separate histograms are computed as the data is accumulated with the appropriate exchange rate and excluding data less than the threshold. Each minute an integrated average level is computed and stored (see Figure 13).

For example, in the following histogram

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Table of Contents Introduction FCC Compliance and Cautionary NoteSimplified Operating Instructions RUN Pause Reset OFFControl Keys CodeSound Level Meter Keys Procedure to Accumulate Event DataDosimeter Keys Time KeysUsing a Printer Setting the ClockRecording the Calibration Level Dumping Raw Data SpecificationsHL3 Print Changing Printer ParametersGeneral Description Weighting CharacteristicsPrinciples of Operation GeneralMicrocomputer Modes Battery Test Testing and CalibrationBattery Replacement WhereOperating Procedure As a Survey or Event Monitor As an Area MonitorEffects of Operators Presence EventsUse with Windscreen Sample Printouts Connections to PrinterPage Page Memory Location Data Memory Map03CO-1FFF Editing PrintoutExtending Battery Life Printer SetupDSR Internal Switches Switch Switch PositionsSetting Internal Switches Code Decoding Interpreting Results TroubleshootingUse of Lavg and TWA Accuracy of Readings Estimating TWA from LavgHints and Good Practices Accessories Service Policy

M-27 specifications

AudioQuest M-27 is a standout speaker designed for audiophiles who demand high performance and exquisite sound quality. As part of AudioQuest's commitment to providing unparalleled audio experiences, the M-27 blends advanced technologies with premium materials to deliver exceptional musical clarity and accuracy.

One of the key features of the M-27 is its innovative driver design, which utilizes a new-generation ceramic cone. This cone is engineered to minimize distortion while enhancing transient response. The result is a speaker that offers a clear, detailed sound across a wide frequency range. The drivers are also matched with an advanced neodymium magnet system, ensuring efficient energy transfer and improved bass response.

The M-27 is equipped with a sophisticated crossover network that has been meticulously designed to maintain the integrity of the audio signal. By employing high-quality components, including precision resistors and capacitors, the crossover effectively divides the audio signal into specific frequency bands, allowing each driver to perform at its best. This attention to detail not only enhances sound quality but also helps to create a more cohesive listening experience.

Another notable characteristic of the M-27 is its sturdy and well-constructed cabinet. Built from high-density MDF, the cabinet is engineered to minimize resonance and vibration, which can color sound. Moreover, AudioQuest has incorporated internal bracing to further enhance structural integrity. The elegantly finished exterior not only adds to the speaker's aesthetic appeal but also serves to complement various home decors.

Connectivity is made simple with the M-27, thanks to its standard speaker terminals that accommodate a wide range of wire gauges. This flexibility allows audiophiles to use their preferred cables for optimal performance. Additionally, the speaker is designed to work seamlessly with a variety of amplifier configurations, making it an adaptable choice for different audio setups.

Incorporating these advanced technologies and design principles, the AudioQuest M-27 is not just a speaker; it's a gateway to an immersive listening experience. With its ability to reproduce sound with remarkable accuracy, it will appeal to discerning listeners looking to elevate their audio playback and enjoy their favorite music in a whole new light. Overall, the M-27 stands as a testament to AudioQuest's dedication to crafting high-quality audio products that meet the needs of serious music enthusiasts.
Top Page Image Contents