Accessories

it is turned on, is reset, or the PAUSE key is pressed. Wait until the sound level has stabilized before entering the run mode.

Always remember to press RUN.

Press PAUSE before pressing PRINT. If in the run mode, the data printed at the beginning of the printout will not agree with the data at the end.

Considerations of Measurement and Accuracy

An integrating meter such as the M-27 Noise Dosimeter can integrate all continuous, intermittent and impulsive sound levels within the range of the instrument. This avoids many of the potential errors created by attempting to read and correctly interpolate sound level meter readings in fluctuating sound fields. However, it is important to use the M-27 correctly and to understand its limits (true of any instru- ment) to achieve its maximum accuracy.

Microphone location generally has the greatest effect on the accuracy of any noise measuring instrument. The correct placement of the M-27 microphone has been discussed under Effects of Operator Presence.

Threshold discontinuity can cause notable differences in readings on various meters if the noise level is near the threshold. Since the instrument assumes that noise even slightly below the threshold is absolute quiet, that noise level is not accumulated into the results while a noise level just slightly higher is accumulated. This is most noticeable in the readings of dose if the threshold is the same as the criterion level.

Peak noise levels greater than the range of the instrument are "clipped" and act as if they were at the maximum level of either 146 dB on the 50 dB range or 126 dB on the 30 dB range.

Minimum noise levels are either at the bottom of the range or at the noise floor of the instrument. For readings which do not have a lower threshold, the accumulated noise will be at these levels.

Crest factor is an almost meaningless term for instruments with crest factors in excess of 30 dB. The M-27 is capable of measuring pulses as short as 1 millisecond with a peak amplitude of 143 dB and a background level of 80 dB. This is a pulse range of 63 dB. The crest factor would depend on how often this pulse occurred but could be greater than 60 dB.

Model WS-5 Windscreen

Refer to page 22 on how to use the windscreen with the M-27 microphone.

Model MB-1 Microphone Bracket

Refer to page 20.

Cables

59-818 36-pin Centronics parallel cable.

59-843 25-pin serial female connector cable. 59-874 25-pin serial male connector cable. 59-758 Computer booster cable.

59-879 9-pin serial female.

Tripods

page 21. Quest supplies two models of tripods for use with the M-27 as an area monitor. For use refer to

BX-9 Battery Change Adapter

To preserve stored data in the M-27 memory during a battery change, the BX-9 Battery Change Adapter may be used. The BX-9 allows you to remotely power the M-27 by plugging it into the printer output connector and therefore keeping the dosimeter powered while disconnecting the battery and replacing it with a fresh one. The BX-9 utilizes pins number 14 and 16 on the printer connector.

M-27 specifications

AudioQuest M-27 is a standout speaker designed for audiophiles who demand high performance and exquisite sound quality. As part of AudioQuest's commitment to providing unparalleled audio experiences, the M-27 blends advanced technologies with premium materials to deliver exceptional musical clarity and accuracy.

One of the key features of the M-27 is its innovative driver design, which utilizes a new-generation ceramic cone. This cone is engineered to minimize distortion while enhancing transient response. The result is a speaker that offers a clear, detailed sound across a wide frequency range. The drivers are also matched with an advanced neodymium magnet system, ensuring efficient energy transfer and improved bass response.

The M-27 is equipped with a sophisticated crossover network that has been meticulously designed to maintain the integrity of the audio signal. By employing high-quality components, including precision resistors and capacitors, the crossover effectively divides the audio signal into specific frequency bands, allowing each driver to perform at its best. This attention to detail not only enhances sound quality but also helps to create a more cohesive listening experience.

Another notable characteristic of the M-27 is its sturdy and well-constructed cabinet. Built from high-density MDF, the cabinet is engineered to minimize resonance and vibration, which can color sound. Moreover, AudioQuest has incorporated internal bracing to further enhance structural integrity. The elegantly finished exterior not only adds to the speaker's aesthetic appeal but also serves to complement various home decors.

Connectivity is made simple with the M-27, thanks to its standard speaker terminals that accommodate a wide range of wire gauges. This flexibility allows audiophiles to use their preferred cables for optimal performance. Additionally, the speaker is designed to work seamlessly with a variety of amplifier configurations, making it an adaptable choice for different audio setups.

Incorporating these advanced technologies and design principles, the AudioQuest M-27 is not just a speaker; it's a gateway to an immersive listening experience. With its ability to reproduce sound with remarkable accuracy, it will appeal to discerning listeners looking to elevate their audio playback and enjoy their favorite music in a whole new light. Overall, the M-27 stands as a testament to AudioQuest's dedication to crafting high-quality audio products that meet the needs of serious music enthusiasts.