ADTRAN OPTI-3 CPE warranty Description, LED Status, Firmware Release, Installation, ACO Button

TOTAL ACCESS OPTI - 3 CONTROLLER MODULE	JOBAID
1550 NM	61184002L4-22B
	0401

OPTI-3

CONTROLLER

CLEI: SOI4JN4D_ _

DESCRIPTION

STATUS OPTICS	DS3	1	DS3	DS3	3	ACO
	-		-2	-

OPTI-3

1184002L4

1550nm

APS TEST ACO

ENABLE

#61184002L4-22B#

LED STATUS

STATUS	● Green	In-Service
	● Yellow	Unit is Out-of-Service – Unassigned
	✷ Flashing Yellow	Unit is Out-of-Service – Maintenance or is ONLINE and inhibited
		from switching
	● Red	Unit has an equipment failure
OPTICS	● Green	Normal Operation
	● Yellow	Soft failure (e.g. RDI)
	✷ Flashing Yellow	Unit in Test (e.g. Loopback)

The Total Access® OPTI-3 Controller Module (OCM) provides an OC-3 interface to the network and three ADD/DROP DS3 interfaces to the Loop. The OCM can be configured for a point-to-point configuration or subtended from 3rd party SONET equipment. The OCM operates in terminal mode only. The compact design mounts in either a rackmount or wallmount chassis, requiring less space and provides optional redundancy. It can automatically switch to the offline unit in the event of optical signal failure or degradation. The modules are fully hot-swappable.

Compliant with SONET standards, the OCM functions as a terminal multiplexer. It supports 1+1 OC-3 equipment and facility protection, 1:1 OC-3 equipment protection (system provisioned for optical Ycable), 1:1 DS3 facility protection, and detects standard optical related alarm conditions. The OCM can be configured to operate redundantly with optional protection of the optics components. It can be upgraded online from un-protected to protected and operating software can be upgraded remotely in Back-to-Back configurations.

The OCM is easily managed with TL1 commands over the Data Communications Channel (DCC) or via Command Line Interface (CLI) through the local craft interface. Additional features include remote alarm transport via DCC and alarm reporting to legacy alarm systems.

FIRMWARE RELEASE

This job aid relates to OPTI-3 System Release 1.3 (Dseries). The menus and functionality are an extension of the prior system release (OPTI-3 System Release 1.2 - Cseries). The latest software is not compatible with System Release 1.1 (Bseries).

INSTALLATION

1 The Total Access OPTI-3 can be installed in either a Rackmount Chassis (RMC), P/N 1184003L1, or a Wallmount Chassis (WMC), P/N 1184001L1. The RMC provides two OCM slots, side by side, with slot A on the left and slot B on the right. (See Figure below.) The WMC provides two OCM slots, positioned vertically with slot A below slot B. Ensure the appropriate chassis is installed before proceeding with the OCM installation.

Carefully insert the OCM halfway into the selected slot. Route the fiber cables through the notch on the OCM front panel and approximately 4 inches past the SC receptacles (to create slack). Gently but firmly push the OCM all the way into the slot, being careful not to pinch the fibers between the front panel and the shelf. Push the latch/ejector tab toward the front panel to lock it into place.

WARNING: Once fully inserted into the chassis, the module will be powered (provided power is connected to the chassis).

2 When the OCM powers up, it performs a self-test. The front panel LEDs illuminate for approximately 8 seconds. The self-test is complete once the STATUS LED illuminates green.

3 If installing a redundant system, repeat the preceding procedure for slot B. If not installing a second OCM, a blank faceplate (P/N 1184005L1) must cover the empty slot.

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

	●	Red	LOS, LOL, and other hard alarms on optical interface
	✷ Flashing Red		Unit in Test (e.g. Loopback) with an alarm present on the Optical
			Interface
DS3-1 – DS3-3 ● Green			Unit is ONLINE (DS3 TX ON)
	● Yellow		Soft failure (e.g. RDI)
	✷ Flashing Yellow		Unit in Test (e.g. Loopback)
	● Red		LOS, LOL, and other hard alarms on DS3 interface
	✷ Flashing Red		Unit in Test (e.g. Loopback) with an alarm present on the DS3
			Interface
ACO	● Yellow		When displayed on the OCM at the CO, indicates acknowledged
			active alarms at the RT
	✷ Flashing Yellow		When displayed on the OCM at the CO, indicates an unacknowl-
			edged active alarms at the RT
	● Red		Acknowledged alarms active on the shelf
	✷ Flashing Red		Unacknowledged alarms active on the shelf

APS PUSHBUTTON

■When depressed simultaneously with the TEST/ENABLE switch on the Offline unit, a switch is forced between the two OCMs.

■When depressed with the TEST/ENABLE switch on the Online unit, it toggles LOCKOUT status.

TEST/ENABLE BUTTON

■When depressed alone, tests all unit LEDs (multicolor LEDs appear YELLOW).

■When depressed simultaneously with the APS switch on the Offline unit, a switch is forced between the two OCMs.

ACO BUTTON

■When depressed after an audible alarm is sounded, silences the alarm.

■When depressed after any other alarm is triggered, acknowledges alarm.

CRAFT INTERFACE

■Provides menu access via RS-232 (Craft) port on the front panel.

■Connects to VT100 compatible terminal using a DB-9 serial cable.

■Requires setting VT100 terminal emulation (to 9600, 19200, 38400, 57600, or 115200 bps), 8 Data Bits, No Parity, 1 Stop Bit, and No Flow Control. (The baud rate default is 9600 bps, which can be modified through the VT100 menu system.

■Provides access to both OCMs installed in the chassis with connection to either OCM craft port.

NOTE: The OPTI-3 is an LR (long reach) optical product. When interfacing with IR (intermediate reach) 3rd party equipment, the optical receive signal may need to be padded to avoid overloading the optical receive signal. The receive signal level should be within − 8 dbm to

−28 dbm for IR equipment.

WARRANTY

ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. U.S. and Canada customer Faxback: 877-457-5007, Document 414.

HANDLING PRECAUTIONS REQUIRED. ■ For a complete Installation and Maintenance Practice (P/N 61184002L4-5): 877-457-5007, Faxback Document 964. Please have your fax number ready. ■