3Com DIGITAL MODEM manual Configuring the 3Com Impact Digital Modem

Page 23

2-6 CHAPTER 2: INSTALLING AND CONFIGURING THE DIGITAL MODEM

9Turn on the 3Com Impact digital modem by toggling the power switch on the back panel to the On position.

See Figure 2-1 for the location of the power switch on the digital modem’s back panel. The indicator LEDs on the front panel (see Figure 2-2) flash momentarily as the unit undergoes a power-up self-test diagnostic.

10Turn on the computer’s power switch and restart.

11Go to the section “Configuration for Apple Macintosh Computer” later in this chapter to configure the 3Com Impact digital modem.

Configuring the 3Com Impact Digital Modem

The 3Com Impact digital modem requires the five essential configuration parameters below before it can operate properly on an ISDN line. Before configuring the digital modem, make sure you have this information readily available. These five parameters are provided to you at the time of installation of your ISDN line by the telephone company installer.

■ISDN Switch Type

■Phone #1 (local directory telephone number)

■SPID #1 (Service Profile Identifier)

■Phone #2 (if required by the telephone company)

■SPID #2 (if required by the telephone company)

Each of these items is stored in special S registers within the digital modem. These S registers are set by issuing ATSxx= commands to the digital modem. The Impact digital modem software will automatically issue the AT commands to set the S registers as part of the configuration process.

The following three sections describe how to configure the 3Com Impact digital modem using the Windows, DOS, or Macintosh operating systems, respectively.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Member of the 3Com Impact product family Isdn External Digital Modem User Guide3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Support from 3Com C-4 Returning Products for Repair C-4 QuickSelectFigures Tables Introduction How to Use This GuideAbout this Guide Conventions Introduction Introduction 3Com Impact digital modem provides the following 3Com Impact Digital Modem FeaturesSimultaneous Data and Voice Capabilities Data CapabilitiesVoice Capabilities 3Com Impact Digital Modem Package Contents 3ComA * J6 Isdn Digital Line Configuration RequirementsISDN-1 Computer System RequirementsAT&T 5ESS EwsdApple Macintosh Requirements IBM PC or Compatible RequirementsDTR Signal Ground GNDClear to Send CTS From digital modem Ring Indicator RI Cabling RequirementsBack Panel Power Switch and Connectors Installing Configuring Digital ModemLED Installing the Digital Modem in an IBM-compatible PC Installing the 3Com Impact Digital ModemInstalling the Digital Modem in an Apple Macintosh Computer Installing the 3Com Impact Digital Modem Configuring the 3Com Impact Digital Modem COM port to which the digital modem is connected Configuration for IBM PC or Compatible ComputerSelect Run from the File menu. In the Run dialog box, type Installing and Configuring the Digital Modem Registers Installing and Configuring the Digital Modem Install Installing and Configuring the Digital Modem Configuration for Apple Macintosh Computer Installing and Configuring the Digital Modem Multilink PPP Calls With Dynamic Bandwidth Allocation Placing and Receiving CallsPlacing Isdn Data Calls Installing and Configuring the Digital Modem Placing Analog Modem Calls Using the Phone Out PortUsing Communications Software to Place Calls Incoming circuit-switched data calls from otherReceiving Calls Using the Phone Out Port Placing Calls Using the Phone Out PortQuickSelect T1 access linesProtocol Support Async-Sync PPP ConversionTroubleshooting Tips TroubleshootingTroubleshooting Monitor the B-1 and B-2 LEDs Troubleshooting Click the Firmware button Firmware dialog box appears If problems persist, refer to Appendix C,Technical SupportDownloading Firmware to Your External Digital Modem Click the Tools button Firmware and Tests buttons appearClick OK AT gets the attention of your 3Com Impact digital modem AT Command SETOverview Type Table B-1 summarizes the AT command set AT Commands REGISTERS, and Result CodesAT Command Set for the 3Com Impact Digital Modem SN= SN?Initial configuration set Settings AT \SCommands \T0 disables inactivity timer defaultATC1 AT Command Set for Internal Analog Fax ModemFlow control Enable MNP mode Stream default Block Results of commandsReceived line signal level Non-error corrected mode onlyAnswer mode detection phase Mode to be negotiated in a DirectMNP extended services Enable inhibits MNP extendedRemote S Registers Isdn S83 Service providerPPP Magic-Number Block Table B-4 lists the 3Com Impact digital modem result codes Digital Modem Result Codes3Com Bulletin Board Service On-line Technical ServicesTo use Ask3Com Log on to CompuServe 3ComFacts Automated Fax ServiceWorld Wide Web Site Ask3Com on CompuServeNorway 800 Sweden 020 0800 Support from Your Network SupplierCountry Fax Number Hong Kong 852 537 Country Fax Number Italy 1678Country Telephone Number Fax Number Support from 3ComReturning Products for Repair To obtain an RMA number, call or faxLimited Warranty 3Com Corporation Bayfront Plaza Interference Handbook Canadian Notice

DIGITAL MODEM specifications

The 3Com Digital Modem represents a significant advancement in communication technology, designed to enhance data transmission over telephone lines. This modem is a part of a lineage of 3Com products that focus on delivering robust networking solutions, tailored for both personal and professional use.

One of the main features of the 3Com Digital Modem is its high-speed data transfer capabilities. With speeds reaching up to 56 Kbps, it allows users to send and receive large amounts of data quickly, which is essential for applications that require efficient data exchange. This speed ensures smoother internet browsing, quicker downloads, and more reliable connections for applications such as video conferencing and online gaming.

The modem is equipped with advanced error correction technologies, including V.42 and V.42bis protocols. These protocols help to maintain data integrity by detecting and correcting errors during transmission. This results in a more reliable connection, reducing the likelihood of dropped calls or corrupted data transfers, which can be particularly frustrating for users engaged in critical business communications.

Another notable characteristic of the 3Com Digital Modem is its compatibility with various operating systems, making it versatile for different users. It supports Windows, Mac, and various other platforms, ensuring that it can be integrated seamlessly into existing systems without the need for extensive configuration. This plug-and-play capability simplifies installation for users, allowing them to get connected quickly and efficiently.

The modem also incorporates an innovative design that facilitates improved heat dissipation, ensuring optimal performance during prolonged use. Its compact form factor makes it suitable for both home and office environments, allowing for easy setup without consuming excessive desk space.

In addition to these features, the 3Com Digital Modem boasts strong security protocols, ensuring that users' data is protected against unauthorized access while being transmitted. This is particularly important in today’s digital landscape, where data breaches and cyber threats are prevalent.

Overall, the 3Com Digital Modem combines speed, reliability, and security, making it a valuable asset for anyone looking to enhance their connectivity experience. Its robust feature set and user-friendly design cater to a broad audience, from casual users to business professionals, reflecting the evolution of modem technology in a digital-first world.
Top Page Image Contents