8e6 Technologies R3000IR quick start Test the R3000 Console Connection

Page 45

Step 2: Test the R3000 Console Connection

Now that the R3000IR is physically installed on your network and you have configured its network settings, you need to test the unit to see if it is set up properly.

A.Restore the setup workstation you used for the Network Setup to its original settings, and connect it to the network hub to create a “network workstation.” (You could also use another workstation already on the network that has Internet access.)

B.Launch IE on the network workstation, and enter the IP address you assigned to LAN 1 (Step 1A, Quick Start menu: administration menu, or Step 1B, Network: LAN Settings, sub-step B). Be sure to include the port information :88 in the address field. For example, if the R3000 were assigned an IP address of 10.10.10.10, you would enter http://10.10.10.10:88 in the browser window’s address field.

C.Click Go. You should be prompted to log into the Administrator console, giving the Username and Password.

If you can access the R3000 Administrator console, the R3000 is functioning on your network and you should proceed to Step 3.

If you cannot access the R3000 Administrator console, please verify the status of the LAN connection in Windows on the network workstation, and then try enabling/disabling the LAN connection. If that fails to work, check the following:

•The R3000IR is turned on.

•The R3000IR is connected to the same hub as your router/firewall.

•Can the PC normally connect to the Internet?

•Is the PC able to ping LAN 1 of the R3000?

•Is the R3000 plugged into a switch instead of a hub?

•Is there a caching server?

•Can the R3000 ping the filtered PC? (Refer to the System Command window in the

Diagnostics section of the R3000 User Guide)

•Did you restart the R3000 after changing the network settings?

•Do you have both LAN ports connected to your network hub?

•If still unsuccessful, contact an 8e6 Technologies solutions engineer or technical sup- port representative.

8e6 R3000IR Quick Start Guide

41

Image 45

Contents Guide Trademarks Contents LED Indicators and Buttons Regulatory Specifications and DisclaimersIndex R3000IR Introduction About this Document Conventions Used in this Document Procedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup PrecautionsRack Mount Instructions Optional Install the Chassis Rails8e6 R3000IR Quick Start Guide Optional Install the Traditional UP Racks 8e6 R3000IR Quick Start Guide Optional Install the Open Racks 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide Install the Chassis into the Rack Power Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Setup Procedures Quick Start Setup RequirementsAdministrator Console Setup Requirements Monitor and Keyboard Setup Quick Start Setup ProceduresSerial Console Setup Link the Workstation to the R3000IRHyperTerminal Setup Procedures 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide Quick Start menu screen Login screenQuick Start menu administration menu LAN2 System Status screenLog Off, Disconnect the Peripherals Console Setup Procedures Preliminary SetupWorkstation Configurations Link the Workstation to the R3000IR Network Setup Boot Up ProcessAccess the R3000IR Administrator Console Log in to R3000 Administrator Console 8e6 R3000IR Quick Start Guide Network Network Operation Mode Network LAN Settings Network NTP Servers 8e6 R3000IR Quick Start Guide Network Regional Setting Physically Connect the R3000IR to the Network Test the R3000 Console Connection Test Filtering or Mobile Client Console Connection Test FilteringTest the Mobile Client Console Connection Activate and Register the R3000 Set Library UpdatesPerform a Complete Library Update Monitor the Library Update Process 8e6 R3000IR Quick Start Guide Log in to the ER Administrator Console Change User Name and Password Set Self-Monitoring Enter the Master Administrator’s E-Mail AddressClient Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Threat Class Groups Threats/Liabilities Filtering ScenariosCategory block Rule blockURL Keywords Custom Lock, Block, Warn, X Strikes, Quota pagesSearch Engine Keywords Custom Category blockedMinimum Filtering Level Override Account bypass Exception URL bypassProxy Patterns II. Bandwidth/Productivity File type blockingTime Quota/Hit Quota Warn option with low filter settings Overall QuotaTime Based Profiles P2P patterns Warn-strikeIM patterns Game patternsStreaming Media patterns Https settings Remote Access patternsSE Keywords Real Time Probe information Custom Block/Warn/X Strikes/Quota pagesWarn Feature with higher thresholds III. General/ProductivityWarn-strike with higher thresholds Time Quota/Hit Quota Local category adds/deletes Customize an 8e6 Supplied CategoryAlways Allow Custom Category IV. Pass/AllowURL exceptions IP exceptionsOverride Accounts Administrator Console, Expiration Screen ER Client, ER Server Statistics Window Diagrams and Descriptions LED Indicator Key Button KeyLED Indicator Color Condition Description Declaration of the Manufacturer or Importer Safety ComplianceElectromagnetic Compatibility EMC Models MSA-002-003Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Index 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide