8e6 Technologies quick start Physically Connect the R3000IR to the Network

Page 44

Physically Connect the R3000IR to the Network

Once your R3000 network parameters are set, you must physically connect the unit to your network. This step requires two standard CAT-5E cables.

NOTE: This section requires you to restart the R3000. If you wish to relocate the R3000IR before connecting it to the network, you must first shut down the server instead of restarting it. To shut down the R3000, go to the navigation panel, click Control, and then select ShutDown. Once the server is shut down, you must power on the R3000IR and then log back into the Administrator console.

A.Restart the server using the steps defined below (i-iii). These steps must always be performed when restarting the R3000IR. Never reset the server by using the power or reset buttons.

i.From the navigation panel of the System section of the console, click Control and select Reboot from the pop-up menu to display the Reboot window.

ii.Click the Reboot button.

iii.From the time you click Reboot, you have approximately 2 minutes to perform sub-steps B through E while the R3000 goes through the reboot process.

B.Disconnect the crossover cable from the R3000IR.

C.Plug one end of a standard CAT-5E cable into the R3000IR’s LAN 1 port.

D.Plug the other end of the CAT-5E cable into an open port on the network hub that handles the Internet traffic you wish to filter.

E.Repeat sub-steps B and C for the R3000IR’s LAN 2 port.

F.Wait until the reboot process has completed, indicated by the drive light staying off for 30 seconds. This process may take 5 to 10 minutes. Proceed to Step 2.

NOTE: If you receive a connection failure message during the reboot process, please disregard it, as this often occurs when there is a change in the IP address.

NOTE:To restart the browser window, close both the R3000 Administrator con- sole and the R3000 Introductory Window. Begin a new session by opening a new browser window and then logging back into the Administrator console.

40	8e6 R3000IR Quick Start Guide

Image 44

Contents Guide Trademarks Contents Index LED Indicators and ButtonsRegulatory Specifications and Disclaimers R3000IR Introduction About this Document Conventions Used in this Document 8e6 Taiwan Procedures8e6 Corporate Headquarters USA Unpack the Unit from the Carton Select a Site for the Server Rack Setup Precautions Rack Mount the ServerOptional Install the Chassis Rails Rack Mount Instructions8e6 R3000IR Quick Start Guide Optional Install the Traditional UP Racks 8e6 R3000IR Quick Start Guide Optional Install the Open Racks 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide Install the Chassis into the Rack Check the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Administrator Console Setup Requirements Setup ProceduresQuick Start Setup Requirements Quick Start Setup Procedures Monitor and Keyboard SetupSerial Console Setup Link the Workstation to the R3000IRHyperTerminal Setup Procedures 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide Login screen Quick Start menu screenQuick Start menu administration menu System Status screen LAN2Log Off, Disconnect the Peripherals Workstation Configurations Console Setup ProceduresPreliminary Setup Link the Workstation to the R3000IR Access the R3000IR Administrator Console Network SetupBoot Up Process Log in to R3000 Administrator Console 8e6 R3000IR Quick Start Guide Network Network Operation Mode Network LAN Settings Network NTP Servers 8e6 R3000IR Quick Start Guide Network Regional Setting Physically Connect the R3000IR to the Network Test the R3000 Console Connection Test the Mobile Client Console Connection Test Filtering or Mobile Client Console ConnectionTest Filtering Set Library Updates Activate and Register the R3000Perform a Complete Library Update Monitor the Library Update Process 8e6 R3000IR Quick Start Guide Log in to the ER Administrator Console Change User Name and Password Enter the Master Administrator’s E-Mail Address Set Self-MonitoringClient Workstation Configuration Launch the ER Client Enter the Password, and Confirm Password Conclusion Threat Class Groups Filtering Scenarios Threats/LiabilitiesCategory block Rule blockCustom Lock, Block, Warn, X Strikes, Quota pages URL KeywordsMinimum Filtering Level Search Engine KeywordsCustom Category blocked Proxy Patterns Override Account bypassException URL bypass Time Quota/Hit Quota II. Bandwidth/ProductivityFile type blocking Time Based Profiles Warn option with low filter settingsOverall Quota Warn-strike P2P patternsStreaming Media patterns IM patternsGame patterns Remote Access patterns Https settingsSE Keywords Custom Block/Warn/X Strikes/Quota pages Real Time Probe informationWarn-strike with higher thresholds Warn Feature with higher thresholdsIII. General/Productivity Time Quota/Hit Quota Customize an 8e6 Supplied Category Local category adds/deletesIV. Pass/Allow Always Allow Custom CategoryURL exceptions IP exceptionsOverride Accounts Administrator Console, Expiration Screen ER Client, ER Server Statistics Window LED Indicator Color Condition Description Diagrams and DescriptionsLED Indicator Key Button Key Safety Compliance Declaration of the Manufacturer or ImporterElectromagnetic Compatibility EMC Models MSA-002-003Electromagnetic Compatibility Class a Notice EC Declaration of Conformity Index 8e6 R3000IR Quick Start Guide 8e6 R3000IR Quick Start Guide