BC-297

Cisco Systems BC-281 manual BC-297

Page 17

Configuring Data-Link Switching Plus

DLSw+ Configuration Task List

The DLSw+ Peer Clusters feature is configured locally on the member peer or on a border peer. Although both options can be configured, we recommend that the cluster-idof a particular peer is defined in either the border peer or on the member peer, but not both because of potential configuration confusion.

	Cisco IOS Bridging and IBM Networking Configuration Guide
	Cisco IOS Bridging and IBM Networking Configuration Guide
78-11737-02		BC-297
78-11737-02		BC-297

Image 17

Contents

BC-281 Configuring Data-Link Switching PlusDLSw Version 2 Standard DLSw StandardIP Multicast BC-282Enhanced Peer-on-Demand Routing Feature DLSw+ FeaturesUDP Unicast Expedited TCP ConnectionBC-284 Local AcknowledgmentLLC2 Session without Local Acknowledgment BC-285BC-286 BC-287 DLSw+ Support for Other SNA FeaturesDefining a DLSw+ Local Peer for the Router Command PurposeDefines the DLSw+ local peer Following is a sample dlsw local peer statementBC-289 Defining a DLSw+ Remote PeerTCP Encapsulation FST Encapsulation TCP/IP with RIF Passthrough EncapsulationDefines a remote peer with FST encapsulation BC-290DLSw Lite Encapsulation Direct EncapsulationDefines a remote peer with direct encapsulation Defines a remote peer with DLSw Lite encapsulationBC-292 Mapping DLSw+ to a Local Data-Link ControlToken Ring BC-293 EthernetBC-294 Enables DLSw+ on an Sdlc interfaceAssociated with this serial interface BC-295 Configuring Advanced FeaturesBC-296 ScalabilityPeer Groups and Border Peers BC-297 BC-298 Enables peer groups and border peersBC-299 Configures peer-on-demand defaultsLocal, remote, and group caches NetBIOS Dial-on-Demand Routing Displays content of group, local and remote cachesFollowing command enables NetBIOS DDR Explorer FirewallsUDP Unicast Feature Following command configures the SNA DDR featureSNA Dial-on-Demand Routing BC-301Promiscuous Peer Defaults Configures a dynamic peerLLC1 Circuits Dynamic PeersAvailability Configures promiscuous peer defaultsLoad Balancing BC-303BC-304 Local routerBackup Peers Configures transparent redundancyEthernet Redundancy Addresses on a transparent bridged are mappedBC-306 Configures a backup peerModes of Operation Network Management Access ControlTraffic Bandwidth and Queueing Management BC-307BC-308 Defines a port listDLSw+ Bridge Group List Static Paths Filter Lists in the Remote-Peer CommandStatic Resources Capabilities Exchange BC-309BC-310 Configuring DLSw+ TimersBC-311 BC-312 Following sections provide DLSw+ configuration examplesBC-313 Router aRouter B DLSw+ with Peer Groups Specified Example BC-314BC-315 Router CFEP BC-316BC-317 Router DRouter E DLSw+ with Sdlc Multidrop Support Configuration ExamplesFollowing example, all devices are type PU BC-318BC-319 Following example, all devices are type PU 2.1 MethodHostname Router a BC-320DLSw+ Translation Between Fddi and Token Ring BC-321BC-322 DLSw+ Translation Between Sdlc and Token Ring Media ExampleSdlc partner 1000.5aed.1f53 d2 sdlc dlsw d2 BC-323BC-324 DLSw+ over Frame Relay Configuration ExampleRing Following three examples describe Qllc support for DLSw+ DLSw+ over Qllc Configuration ExamplesExample BC-325BC-326 DLSw+ with RIF Passthrough Configuration ExampleBC-327 DLSw+ with Enhanced Load Balancing Configuration ExampleBC-328 DLSw+ Peer Cluster Feature Configuration ExampleBC-329 DLSWRTR2BC-330 Shows a DLSw+ border peer network configured with DLSw+ RsvpBC-331 DLSw+ with Ethernet Redundancy Configuration ExampleBC-332 DLSw+ with Ethernet Redundancy in a Switched EnvironmentBC-333 BC-334

Related manuals

Cisco Systems BC-281 manual BC-297