Cisco Systems BC-281 manual BC-320, Hostname Router a

Page 40

Configuring Data-Link Switching Plus

DLSw+ Configuration Examples

Router A

source-bridge ring-group 1111 dlsw local-peer peer-id 10.2.2.2 dlsw remote-peer 0 tcp 10.1.1.1 interface loopback 0

ip address 10.2.2.2 255.255.255.0 interface TokenRing 0

no ip address ring-speed 16

source-bridge 2 1111 source-bridge spanning

Router B

dlsw local-peer peer-id 10.1.1.1 dlsw remote-peer 0 tcp 10.2.2.2 interface loopback 0

ip address 10.1.1.1 255.255.255.0 interface serial 0

mtu 4096

no ip address encapsulation sdlc no keepalive nzri-encoding clockrate 9600

sdlc vmac 4000.3745.0000 sdlc N1 48016

sdlc address 04 echo

sdlc partner 4000.1111.0020 04 sdlc dlsw 4

DLSw+ Translation Between Ethernet and Token Ring Configuration Example

DLSw+ also supports Ethernet media. The configuration is similar to other DLSw+ configurations, except for configuring for a specific media. The following example shows Ethernet media (see Figure 135).

Figure 135 DLSw+ Translation Between Ethernet and Token Ring

Router A

Router B

e0

 

e1/2

128.207.111.1

128.207.1.145

Token

Ring

7

AS/400

S3584

Router A

hostname Router A

!

dlsw local-peer peer-id 128.207.111.1 dlsw remote-peer 0 tcp 128.207.1.145

 

Cisco IOS Bridging and IBM Networking Configuration Guide

BC-320

78-11737-02

Page 39 Page 41
Image 40
Page 39 Page 41
Contents
Configuring Data-Link Switching Plus BC-281DLSw Standard DLSw Version 2 StandardIP Multicast BC-282DLSw+ Features Enhanced Peer-on-Demand Routing FeatureUDP Unicast Expedited TCP ConnectionLocal Acknowledgment BC-284BC-285 LLC2 Session without Local AcknowledgmentBC-286 DLSw+ Support for Other SNA Features BC-287Command Purpose Defining a DLSw+ Local Peer for the RouterDefines the DLSw+ local peer Following is a sample dlsw local peer statementTCP Encapsulation Defining a DLSw+ Remote PeerBC-289 TCP/IP with RIF Passthrough Encapsulation FST EncapsulationDefines a remote peer with FST encapsulation BC-290Direct Encapsulation DLSw Lite EncapsulationDefines a remote peer with direct encapsulation Defines a remote peer with DLSw Lite encapsulationToken Ring Mapping DLSw+ to a Local Data-Link ControlBC-292 Ethernet BC-293Associated with this serial interface Enables DLSw+ on an Sdlc interfaceBC-294 Configuring Advanced Features BC-295Peer Groups and Border Peers ScalabilityBC-296 BC-297 Enables peer groups and border peers BC-298Local, remote, and group caches Configures peer-on-demand defaultsBC-299 Displays content of group, local and remote caches NetBIOS Dial-on-Demand RoutingFollowing command enables NetBIOS DDR Explorer FirewallsFollowing command configures the SNA DDR feature UDP Unicast FeatureSNA Dial-on-Demand Routing BC-301Configures a dynamic peer Promiscuous Peer DefaultsLLC1 Circuits Dynamic PeersConfigures promiscuous peer defaults AvailabilityLoad Balancing BC-303Local router BC-304Configures transparent redundancy Backup PeersEthernet Redundancy Addresses on a transparent bridged are mappedModes of Operation Configures a backup peerBC-306 Access Control Network ManagementTraffic Bandwidth and Queueing Management BC-307DLSw+ Bridge Group List Defines a port listBC-308 Filter Lists in the Remote-Peer Command Static PathsStatic Resources Capabilities Exchange BC-309Configuring DLSw+ Timers BC-310BC-311 Following sections provide DLSw+ configuration examples BC-312Router B Router aBC-313 BC-314 DLSw+ with Peer Groups Specified ExampleRouter C BC-315BC-316 FEPRouter D BC-317DLSw+ with Sdlc Multidrop Support Configuration Examples Router EFollowing example, all devices are type PU BC-318Following example, all devices are type PU 2.1 Method BC-319BC-320 Hostname Router aBC-321 DLSw+ Translation Between Fddi and Token RingDLSw+ Translation Between Sdlc and Token Ring Media Example BC-322BC-323 Sdlc partner 1000.5aed.1f53 d2 sdlc dlsw d2Ring DLSw+ over Frame Relay Configuration ExampleBC-324 DLSw+ over Qllc Configuration Examples Following three examples describe Qllc support for DLSw+Example BC-325DLSw+ with RIF Passthrough Configuration Example BC-326DLSw+ with Enhanced Load Balancing Configuration Example BC-327DLSw+ Peer Cluster Feature Configuration Example BC-328DLSWRTR2 BC-329Shows a DLSw+ border peer network configured with DLSw+ Rsvp BC-330DLSw+ with Ethernet Redundancy Configuration Example BC-331DLSw+ with Ethernet Redundancy in a Switched Environment BC-332BC-333 BC-334
Related manuals
Manual 54 pages 58.74 Kb