Cisco Systems BC-281 manual Router a, Router B, BC-313

Page 33

Configuring Data-Link Switching Plus

DLSw+ Configuration Examples

Figure 131 illustrates a DLSw+ configuration with local acknowledgment. Because the RIF is terminated, the ring group numbers do not have to be the same.

Figure 131 DLSw+ with Local Acknowledgment—Simple Configuration

 

Router A

Ring Group

Ring Group

Router B

 

 

10

12

 

 

Token

 

 

Token

 

Ring

 

 

Ring

 

25

 

 

5

37x5

10.2.25.1

 

 

10.2.5.2

 

 

 

 

Router A

source-bridge ring-group 10

!

dlsw local-peer peer-id 10.2.25.1 dlsw remote-peer 0 tcp 10.2.5.2

interface loopback 0

ip address 10.2.25.1 255.255.255.0

!

interface tokenring 0 no ip address ring-speed 16 source-bridge 25 1 10 source-bridge spanning

Router B

source-bridge ring-group 12

dlsw local-peer peer-id 10.2.5.2 dlsw remote-peer 0 tcp 10.2.25.1

interface loopback 0

ip address 10.2.5.2 255.255.255.0

!

interface tokenring 0 no ip address ring-speed 16 source-bridge 5 1 12 source-bridge spanning

S3241

3x74

 

 

Cisco IOS Bridging and IBM Networking Configuration Guide

 

 

 

 

 

 

 

78-11737-02

 

 

BC-313

 

 

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
BC-281 Configuring Data-Link Switching PlusDLSw Version 2 Standard DLSw StandardIP Multicast BC-282Enhanced Peer-on-Demand Routing Feature DLSw+ FeaturesUDP Unicast Expedited TCP ConnectionBC-284 Local AcknowledgmentLLC2 Session without Local Acknowledgment BC-285BC-286 BC-287 DLSw+ Support for Other SNA FeaturesDefining a DLSw+ Local Peer for the Router Command PurposeDefines the DLSw+ local peer Following is a sample dlsw local peer statementDefining a DLSw+ Remote Peer TCP EncapsulationBC-289 FST Encapsulation TCP/IP with RIF Passthrough EncapsulationDefines a remote peer with FST encapsulation BC-290DLSw Lite Encapsulation Direct EncapsulationDefines a remote peer with direct encapsulation Defines a remote peer with DLSw Lite encapsulationMapping DLSw+ to a Local Data-Link Control Token RingBC-292 BC-293 EthernetEnables DLSw+ on an Sdlc interface Associated with this serial interfaceBC-294 BC-295 Configuring Advanced FeaturesScalability Peer Groups and Border PeersBC-296 BC-297 BC-298 Enables peer groups and border peersConfigures peer-on-demand defaults Local, remote, and group cachesBC-299 NetBIOS Dial-on-Demand Routing Displays content of group, local and remote cachesFollowing command enables NetBIOS DDR Explorer FirewallsUDP Unicast Feature Following command configures the SNA DDR featureSNA Dial-on-Demand Routing BC-301Promiscuous Peer Defaults Configures a dynamic peerLLC1 Circuits Dynamic PeersAvailability Configures promiscuous peer defaultsLoad Balancing BC-303BC-304 Local routerBackup Peers Configures transparent redundancyEthernet Redundancy Addresses on a transparent bridged are mappedConfigures a backup peer Modes of OperationBC-306 Network Management Access ControlTraffic Bandwidth and Queueing Management BC-307Defines a port list DLSw+ Bridge Group ListBC-308 Static Paths Filter Lists in the Remote-Peer CommandStatic Resources Capabilities Exchange BC-309BC-310 Configuring DLSw+ TimersBC-311 BC-312 Following sections provide DLSw+ configuration examplesRouter a Router BBC-313 DLSw+ with Peer Groups Specified Example BC-314BC-315 Router CFEP BC-316BC-317 Router DRouter E DLSw+ with Sdlc Multidrop Support Configuration ExamplesFollowing example, all devices are type PU BC-318BC-319 Following example, all devices are type PU 2.1 MethodHostname Router a BC-320DLSw+ Translation Between Fddi and Token Ring BC-321BC-322 DLSw+ Translation Between Sdlc and Token Ring Media ExampleSdlc partner 1000.5aed.1f53 d2 sdlc dlsw d2 BC-323DLSw+ over Frame Relay Configuration Example RingBC-324 Following three examples describe Qllc support for DLSw+ DLSw+ over Qllc Configuration ExamplesExample BC-325BC-326 DLSw+ with RIF Passthrough Configuration ExampleBC-327 DLSw+ with Enhanced Load Balancing Configuration ExampleBC-328 DLSw+ Peer Cluster Feature Configuration ExampleBC-329 DLSWRTR2BC-330 Shows a DLSw+ border peer network configured with DLSw+ RsvpBC-331 DLSw+ with Ethernet Redundancy Configuration ExampleBC-332 DLSw+ with Ethernet Redundancy in a Switched EnvironmentBC-333 BC-334
Related manuals
Manual 54 pages 58.74 Kb