Cisco Systems 566, 511 manual Installing the Chassis on a Tabletop

Page 69

Chapter 3 Installing the Content Engine

Installing a CE-511 or CE-566 Unit

Note Leave enough slack in the cables to allow for sliding the Content Engine in or out of the rack.

To remove the Content Engine from the rack, reverse these instructions. Store these installation instructions with your Content Engine documentation for future use.

Installing the Chassis on a Tabletop

When you install a Content Engine on a workbench or tabletop, ensure that the surface is clean and in a safe location and that you have considered the following:

•The chassis should be installed off the floor. (Dust that accumulates on the floor is drawn into the interior of the chassis by the cooling fans. Excessive dust inside the Content Engine can cause overtemperature conditions and component failures.)

•There must be approximately 19 inches (48.26 cm) of clearance at the front and rear of the chassis for accessing network cables or equipment.

•The Content Engine must receive adequate ventilation (it is not being installed in an enclosed cabinet where ventilation is inadequate).

Follow these steps to install the Content Engine on a workbench or tabletop:

 

Step 1

Remove any debris and dust from the tabletop or workbench, as well as from the

 

 

surrounding area. Also make sure that your path between the Content Engine and

 

 

its new location is unobstructed.

 

Step 2

Attach the rubber feet to the bottom of the chassis. The rubber feet have an

 

 

adhesive backing. Peel the protective tape off the adhesive and stick the feet to the

 

 

bottom of a clean chassis surface. Place one foot in each corner.

 

Step 3

Place the chassis on the tabletop or workbench.

 

Step 4

Ensure that no exhaust air from other equipment will be drawn into the chassis.

 

 

Also, ensure that there is adequate clearance at the front and rear of the chassis.

 

 

 

 

 

 

 

Cisco Content Engine 511 and 566 Hardware Installation Guide

 

 

 

 

 

 

OL-5756-01

 

 

3-11

 

 

 

Page 68 Page 70
Image 69
Page 68 Page 70
Contents Cisco Content Engine 511 and 566 Hardware Installation Guide Page Cisco Content Engine 511 and 566 Hardware Installation Guide Page N T E N T S Specifications Vii Preparing and Installing a Fibre Channel AdapterViii Document Objectives PrefaceAudience Document OrganizationChapter Title Description Convention Description Document ConventionsXii Waarschuwing Belangrijke Veiligheidsinstructies Varoitus Tärkeitä TurvallisuusohjeitaXiii Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaXiv Aviso Instruções Importantes DE Segurança TA Vare PÅ Disse InstruksjoneneXvi Varning! Viktiga SäkerhetsanvisningarXvii Xviii GEM Disse AnvisningerXix OL-5756-01 Cisco.com Obtaining DocumentationOrdering Documentation XxiObtaining Technical Assistance Documentation FeedbackCisco Technical Support Website XxiiXxiii Submitting a Service RequestXxiv Definitions of Service Request SeverityXxv Xxvi Introduction Introducing the Content EngineCE-511 and CE-566-Front View Model Product NumberCE-566 Back Panel with Scsi Port Connector Content Engine Specification DescriptionFunctional Description Content Caching Device Content Delivery Network ComponentHardware Features CE-511 and CE-566 Front Panel Front Panel Control ButtonsColor State Description LED Indicators10BASE-T/100BASE-TX Indicator Color State DescriptionFibre Channel Adapter LEDs State MeaningInput/Output Ports and Connectors 7describes the back panel ports and receptacles Ethernet Port Scsi Port Video Port Pin Number Destination DestinationSpecifications PCM 6 or compressed audio coding 3 AC-3 Specification Description Regulatory Compliance EMC Class a Warning Statements Class a Warning for Hungary OL-5756-01 Safety Warnings Preparing to Install the Content EngineOL-5756-01 Preparing to Install the Content Engine Safety Warnings General Precautions Safety GuidelinesPreparing to Install the Content Engine Safety Guidelines Protecting Against Electrostatic Discharge Rack Installation Safety GuidelinesPreparing to Install the Content Engine Safety Guidelines OL-5756-01 Tools and Parts Required Installing the Content EngineInstalling a CE-511 or CE-566 Unit Orientation for 19-inch rack Installing the Chassis in a 2-Post RackInstalling the Chassis in the Rack Installing the Chassis in a 4-Post RackRack Installation Kit Installing Clip Nuts or Cage Nuts Removing the Inner Slide Rail Attaching the Inner Slide Rail to the Content Engine Attaching the Slide Rails to the Rack Inserting the Inner Slide Rails Installing the Chassis on a Tabletop Connecting Cables Review the information in the Safety Warnings section on Connecting Power and Booting the SystemChecking the LEDs Removing or Replacing a Content EngineOL-5756-01 OL-5756-01 Removing the Cover and Bezel Installing Hardware OptionsRemoving the Content Engine Cover Removing the Content Engine Bezel Installing AdaptersInstalling Hardware Options Installing Adapters Installing an Mpeg Decoder Adapter Removing the Expansion Slot Cover Installing an Adapter in PCI-X Slot Preparing and Installing a Fibre Channel Adapter Preparing to Install the Adapter Installing the Fibre Channel Adapter Hardware Problems Working with Hard Disk Drives Installing a Hard Disk Drive in the CE-511Installing a Sata Hard Disk on CE-511 Installing a Hard Disk Drive in the CE-566 Scsi hard disk drive Screws Hard disk drive tray Assigning Scsi IDs Completing the InstallationInstalling the Content Engine Cover and Bezel Installing the Content Engine Cover Checking the Basics Troubleshooting the System HardwareChecking Connections and Switches OL-5756-01 OL-5756-01 Maintaining Your Site Environment Maintaining the Content EngineTemperature Humidity AltitudeDust and Particles Electrostatic Discharge CorrosionMagnetism Electromagnetic and Radio Frequency InterferencePower Source Interruptions Uninterruptible Power Supplies Using Power Protection DevicesSurge Protectors Line ConditionersCisco Content Engine 511 and 566 Hardware Installation Guide IN-1 D EIN-2 ESDIN-3 IN-4 IN-5 RFIIN-6 Wccp

566, 511 specifications

Cisco Systems 511,566 is a cutting-edge networking solution designed to enhance the capabilities of businesses in today's digital landscape. As part of Cisco's extensive portfolio, this device integrates advanced features and technologies aimed at improving performance, security, and reliability in network operations.

One of the main features of the Cisco Systems 511,566 is its support for high-speed data transfer. With a robust processing capability, it can handle large volumes of data traffic, making it ideal for enterprises that require rapid and reliable connectivity. The device leverages advanced routing protocols to optimize data paths, ensuring efficient bandwidth utilization.

In terms of security, the Cisco Systems 511,566 incorporates state-of-the-art security measures that protect critical business information. It features built-in firewalls, intrusion detection systems, and secure VPN capabilities. This multi-layered security architecture helps safeguard against external threats while ensuring that data remains confidential and secure.

The device is also equipped with scalable architecture, allowing businesses to expand their network capabilities as they grow. It supports multiple interfaces and connectivity options, enabling seamless integration with existing infrastructure. This scalability makes it a flexible choice for organizations that anticipate changes in their networking needs.

Cisco's commitment to innovation is evident in the intelligent technologies integrated into the 511,566. It utilizes machine learning algorithms to monitor network performance in real time, allowing for proactive troubleshooting and optimization. With these insights, IT teams can quickly identify issues and mitigate them before they impact business operations.

Another characteristic of the Cisco Systems 511,566 is its user-friendly interface. The device is designed with intuitive management tools that simplify configuration and monitoring tasks. This ease of use enables IT professionals to manage the network efficiently without extensive training.

Furthermore, the 511,566 is capable of supporting IoT (Internet of Things) devices. With the increasing number of connected devices in the workplace, having reliable support for IoT is crucial. This capability ensures that businesses can leverage smart technologies to enhance productivity and operational efficiency.

In conclusion, Cisco Systems 511,566 stands out as a powerful networking solution that combines speed, security, scalability, and intelligence. Its advanced features make it an excellent choice for organizations looking to enhance their network capabilities and support future growth in the ever-evolving digital age.
Top Page Image Contents