Cisco Systems 511, 566 manual Temperature

Page 98

Chapter 6 Maintaining the Content Engine

Maintaining Your Site Environment

Temperature

Temperature extremes can cause a variety of problems, including premature aging and failure of chips or mechanical failure of devices. Extreme temperature fluctuations can cause chips to become loose in their sockets and can cause expansion and contraction of disk drive platters, resulting in read or write data errors.

To minimize the negative effects of temperature on system performance, follow these guidelines:

•Ensure that the system is operated in an environment no colder than 50°F (10°C) or hotter than 95°F (35°C).

•Ensure that the system has adequate ventilation. Do not place it within a closed-in wall unit or on top of cloth, which can act as insulation. Do not place it where it will receive direct sunlight, particularly in the afternoon. Do not place it next to a heat source of any kind, including heating vents during winter.

Adequate ventilation is particularly important at high altitudes. System performance may not be optimum when the system is operating at high temperatures as well as high altitudes.

•Make sure that all slots and openings on the system remain unobstructed, especially the fan vent on the back of the system.

•Clean the system at regular intervals to avoid any buildup of dust and debris, which can cause a system to overheat.

•If the system has been exposed to abnormally cold temperatures, allow a

2-hour warm-up period to bring it up to normal operating temperature before turning it on. Failure to do so may cause damage to internal components, particularly the hard disk drive.

•If intermittent system failures are noticed, try reseating any socketed chips, which might have become loose because of temperature fluctuations.

 

Cisco Content Engine 511 and 566 Hardware Installation Guide

6-2

OL-5756-01

Page 97 Page 99
Image 98
Page 97 Page 99
Contents Cisco Content Engine 511 and 566 Hardware Installation Guide Page Cisco Content Engine 511 and 566 Hardware Installation Guide Page N T E N T S Specifications Preparing and Installing a Fibre Channel Adapter ViiViii Preface Document ObjectivesChapter Title Description AudienceDocument Organization Document Conventions Convention DescriptionXii Xiii Waarschuwing Belangrijke VeiligheidsinstructiesVaroitus Tärkeitä Turvallisuusohjeita Xiv Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza TA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaVarning! Viktiga Säkerhetsanvisningar XviXvii GEM Disse Anvisninger XviiiXix OL-5756-01 Ordering Documentation Obtaining DocumentationCisco.com XxiCisco Technical Support Website Documentation FeedbackObtaining Technical Assistance XxiiSubmitting a Service Request XxiiiDefinitions of Service Request Severity XxivXxv Xxvi Introducing the Content Engine IntroductionModel Product Number CE-511 and CE-566-Front ViewCE-566 Back Panel with Scsi Port Connector Functional Description Content EngineSpecification Description Content Delivery Network Component Content Caching DeviceHardware Features Front Panel Control Buttons CE-511 and CE-566 Front PanelLED Indicators Color State DescriptionIndicator Color State Description 10BASE-T/100BASE-TXState Meaning Fibre Channel Adapter LEDsInput/Output Ports and Connectors 7describes the back panel ports and receptacles Ethernet Port Scsi Port Video Port Destination Pin Number DestinationSpecifications PCM 6 or compressed audio coding 3 AC-3 Specification Description Regulatory Compliance EMC Class a Warning Statements Class a Warning for Hungary OL-5756-01 Preparing to Install the Content Engine Safety WarningsOL-5756-01 Preparing to Install the Content Engine Safety Warnings Safety Guidelines General PrecautionsPreparing to Install the Content Engine Safety Guidelines Rack Installation Safety Guidelines Protecting Against Electrostatic DischargePreparing to Install the Content Engine Safety Guidelines OL-5756-01 Installing the Content Engine Tools and Parts RequiredInstalling a CE-511 or CE-566 Unit Installing the Chassis in a 2-Post Rack Orientation for 19-inch rackInstalling the Chassis in a 4-Post Rack Installing the Chassis in the RackRack Installation Kit Installing Clip Nuts or Cage Nuts Removing the Inner Slide Rail Attaching the Inner Slide Rail to the Content Engine Attaching the Slide Rails to the Rack Inserting the Inner Slide Rails Installing the Chassis on a Tabletop Connecting Cables Connecting Power and Booting the System Review the information in the Safety Warnings section onRemoving or Replacing a Content Engine Checking the LEDsOL-5756-01 OL-5756-01 Installing Hardware Options Removing the Cover and BezelRemoving the Content Engine Cover Installing Adapters Removing the Content Engine BezelInstalling Hardware Options Installing Adapters Installing an Mpeg Decoder Adapter Removing the Expansion Slot Cover Installing an Adapter in PCI-X Slot Preparing and Installing a Fibre Channel Adapter Preparing to Install the Adapter Installing the Fibre Channel Adapter Hardware Problems Installing a Hard Disk Drive in the CE-511 Working with Hard Disk DrivesInstalling a Sata Hard Disk on CE-511 Installing a Hard Disk Drive in the CE-566 Scsi hard disk drive Screws Hard disk drive tray Completing the Installation Assigning Scsi IDsInstalling the Content Engine Cover and Bezel Installing the Content Engine Cover Troubleshooting the System Hardware Checking the BasicsChecking Connections and Switches OL-5756-01 OL-5756-01 Maintaining the Content Engine Maintaining Your Site EnvironmentTemperature Dust and Particles HumidityAltitude Corrosion Electrostatic DischargeElectromagnetic and Radio Frequency Interference MagnetismPower Source Interruptions Surge Protectors Using Power Protection DevicesUninterruptible Power Supplies Line ConditionersCisco Content Engine 511 and 566 Hardware Installation Guide D E IN-1ESD IN-2IN-3 IN-4 RFI IN-5Wccp IN-6

566, 511 specifications

Cisco Systems 511,566 is a cutting-edge networking solution designed to enhance the capabilities of businesses in today's digital landscape. As part of Cisco's extensive portfolio, this device integrates advanced features and technologies aimed at improving performance, security, and reliability in network operations.

One of the main features of the Cisco Systems 511,566 is its support for high-speed data transfer. With a robust processing capability, it can handle large volumes of data traffic, making it ideal for enterprises that require rapid and reliable connectivity. The device leverages advanced routing protocols to optimize data paths, ensuring efficient bandwidth utilization.

In terms of security, the Cisco Systems 511,566 incorporates state-of-the-art security measures that protect critical business information. It features built-in firewalls, intrusion detection systems, and secure VPN capabilities. This multi-layered security architecture helps safeguard against external threats while ensuring that data remains confidential and secure.

The device is also equipped with scalable architecture, allowing businesses to expand their network capabilities as they grow. It supports multiple interfaces and connectivity options, enabling seamless integration with existing infrastructure. This scalability makes it a flexible choice for organizations that anticipate changes in their networking needs.

Cisco's commitment to innovation is evident in the intelligent technologies integrated into the 511,566. It utilizes machine learning algorithms to monitor network performance in real time, allowing for proactive troubleshooting and optimization. With these insights, IT teams can quickly identify issues and mitigate them before they impact business operations.

Another characteristic of the Cisco Systems 511,566 is its user-friendly interface. The device is designed with intuitive management tools that simplify configuration and monitoring tasks. This ease of use enables IT professionals to manage the network efficiently without extensive training.

Furthermore, the 511,566 is capable of supporting IoT (Internet of Things) devices. With the increasing number of connected devices in the workplace, having reliable support for IoT is crucial. This capability ensures that businesses can leverage smart technologies to enhance productivity and operational efficiency.

In conclusion, Cisco Systems 511,566 stands out as a powerful networking solution that combines speed, security, scalability, and intelligence. Its advanced features make it an excellent choice for organizations looking to enhance their network capabilities and support future growth in the ever-evolving digital age.
Top Page Image Contents