Samsung SWL-3000AP CMDt,p,h Enter Current Channel Enter new Channel 1-14, CMDt,p,h Enter Dhcp

Page 69

③Select the following order to change Wireless Channel.

CMD(t,p,h): 2 ↵	Enter Current Channel
	Enter Current Channel
Enter new Channel {1-14}: 11 ↵

Enter the proper channel number after the phrase “Enter new Channel {1- 14}:”. Then, press [ENTER : ↵ ]. Channel index should be between 1 and 14(differs from country to country).

Notice : If you are operating two or more Access Points in the adjoining cells, keep the appropriate channel distance to avoid the interference. We recommend you to keep the distance of at least 4 channels in the adjoining cells.

④Only if AP is used for DHCP Client, you set DHCP Client with “Enabled”. In this case, there is no need to set ⑤, ⑥, ⑦ below. The default setting is “Disabled”.

	CMD(t,p,h): 3 ↵	Enter DHCP	Client
	CMD(t,p,h): 3 ↵	Setting Selection
		Setting Selection
	Enter new DHCP Client {enable, disable}: disable ↵

⑤Select the following order to set IP Address.

CMD(t,p,h): 4 ↵	Enter IP Address
	Enter IP Address
Enter new IP Address : 16.3.60.208 ↵

Enter the proper IP address after “Enter new IP Address :”. Then, press

[ENTER : ↵ ]. Consult your system administrator for setting the proper value of IP Address.

65

Image 69

Contents SWL-3000AP Series Access Point User’s Guide This Guide is a copyright Table of Contents Appendix Ⅰ Introduction Status Wireless RS-232C RJ-45 Connector Ethernet Power Installation SWL-3000APDA SWL-3300AP SWL-3300APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Enter the Same Essid Channel of two APs in PTP Mode Page Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Bridge Table and Protocol Management Using AP Manager ProtocolManagement Box Page Select Enabled Select Protocol Which You Do Not Want Select Server Tab NAT Setting IP Address Subnet Mask Setting NAT Setting Using AP ManagerConfirm NAT Setting Confirm NAT Setting Page Page Select Server Dhcp Server Setting Using AP ManagerSelect Empty Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Select on Menu Bar Select on Dialogue Box Adsl and Cable Modem Connection Setting Using AP ManagerSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Select Encryption Start Encryption Setting Encryption Setting Using AP ManagerPage Confirm Encryption Setting Confirm 6440-bit Encryption SettingDeny Pass User Access Control Setting Using AP ManagerSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Scope of Number of Packet Transmitted per Second Line SettingSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Communication Page Page MagicLAN AP Basic Setting Using RS-232CCOM PortCMDt,p,h Enter Menu Number CMDt,p,h Enter Essid Enter new Essid Max Ascii testAPEnter new Dhcp Client enable, disable disable Setting SelectionCMDt,p,h Enter Current Channel Enter new Channel 1-14 CMDt,p,h Enter DhcpCMDt,p,h Enter Gateway Address Enter new Gateway Address CMDt,p,h Enter Subnet Mask Enter new Subnet MaskCMDt,p,h Select AdvancedPage Select Save and reboot TestAP All items was set to the default values Load default values Using RS-232CCOM PortVia serial Firmware Upgrade Using RS-232CCOM PortApfirm Page 1K Xmodem Appendix Ⅰ Explanation of Basic Configuration to use AP ManagerList Box Dialogue Box Button Bar Menu BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page General Appendix Ⅱ. SpecificationManagement Features Environmental Information We value your feedback