Samsung SWL-3000AP manual Installation

Page 7

2. Installation

①Choose the place with the consideration of power outlet and network connection (RJ-45 Cable connection) to install the Access Point.

②Plug in the power cord to the power outlet and the power adapter.

Plug in the DC output to “DC in”. Make sure that the “Power” LED is on. If the “Power” LED is not on, please check the connections of the power cord.

Notice : Use the supplied power adapter(DC 5V, 2A) only to prevent the permanent failure of AP.

③Confirm that “Wireless” LED of AP blinks.

If not, confirm that Wireless LAN Card of AP is properly mounted in case for 3000AP and 3000AP(DA). For 3300AP and 3300AP(DA), contact where you purchase the product. The card should be inserted or extracted when the power is off, and we are not responsible for any product failure due to disassemble by users.

Notice : Use the supplied Wireless LAN card(3.3V) only to prevent the permanent failure of AP.

④Attach UTP Ethernet cable to the RJ-45 Connector.

Make sure that the “Ethernet” LED is on. If the “Ethernet” LED is on, you can use the existing network with the Access Point; otherwise check the UTP cable connections.

⑤Attach RS-232C serial cable to the Access Point and the PC.

The parameters of Access Point can be configured through the connection of RS-232C serial cable to the PC(Refer to Chapter 17).

⑥When AP Manager is used, you may skip the step ⑤.

⑦Change settings of AP according to user’ s selection referring User’ s Guide.

3

Image 7

Contents SWL-3000AP Series Access Point User’s Guide This Guide is a copyright Table of Contents Appendix Ⅰ Introduction Status Wireless RS-232C RJ-45 Connector Ethernet Power Installation SWL-3000APDA SWL-3300AP SWL-3300APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Enter the Same Essid Channel of two APs in PTP Mode Page Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Protocol Bridge Table and Protocol Management Using AP ManagerManagement Box Page Select Enabled Select Protocol Which You Do Not Want Select Server Tab NAT Setting IP Address Subnet Mask Setting NAT Setting Using AP ManagerConfirm NAT Setting Confirm NAT Setting Page Page Select Server Dhcp Server Setting Using AP ManagerSelect Empty Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Select on Menu Bar Select on Dialogue Box Adsl and Cable Modem Connection Setting Using AP ManagerSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Select Encryption Start Encryption Setting Encryption Setting Using AP ManagerPage Confirm Encryption Setting Confirm 6440-bit Encryption SettingDeny Pass User Access Control Setting Using AP ManagerSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Scope of Number of Packet Transmitted per Second Line SettingSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Communication Page Page CMDt,p,h Enter Essid Enter new Essid Max Ascii testAP AP Basic Setting Using RS-232CCOM PortMagicLAN CMDt,p,h Enter Menu NumberCMDt,p,h Enter Dhcp Setting SelectionEnter new Dhcp Client enable, disable disable CMDt,p,h Enter Current Channel Enter new Channel 1-14CMDt,p,h Enter Gateway Address Enter new Gateway Address CMDt,p,h Enter Subnet Mask Enter new Subnet MaskCMDt,p,h Select AdvancedPage Select Save and reboot TestAP All items was set to the default values Load default values Using RS-232CCOM PortVia serial Firmware Upgrade Using RS-232CCOM PortApfirm Page 1K Xmodem Appendix Ⅰ Explanation of Basic Configuration to use AP ManagerList Box Dialogue Box Button Bar Menu BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page General Appendix Ⅱ. SpecificationManagement Features Environmental Information We value your feedback