Samsung SWL-3000AP AP Basic Setting Using RS-232CCOM Port, MagicLAN, CMDt,p,h Enter Menu Number

Page 68

18. AP Basic Setting Using RS-232C(COM Port)

①Choose [Basic] menu on [ROOT] menu.

==================================================

Samsung SWL-3300AP Configuration

==================================================

[ Basic ]
1.	ESSID	MagicLAN
2.	Channel	3
3.	DHCP Client	Disabled
4.	IP Address	10.0.0.2
5.	Subnet Mask	255.255.255.0
6.	Gateway Address	10.0.0.1
7.	Description	MagicLAN 11Mbps AP

CMD(t,p,h):

Enter Menu Number

②Select the following order to set Wireless LAN ESSID.

CMD(t,p,h): 1 ↵	Enter ESSID
	Enter ESSID
Enter new ESSID {Max. 32 ASCII}: test_AP ↵

Enter the proper ESSID (strings up to 32 characters) on “Enter new ESSID {Max. 32 ASCII}:”, and press [ENTER : ↵ ]. ESSID must consist of alphabetic and numeric characters, excluding space and special characters. (Capital• Small letter distinction)

New setting appears on [Basic] menu. Type t and press [ENTER : ↵ ] if you would like to return to the top menu [ROOT]. Otherwise, you will remain in [Basic] menu.

64

Image 68

Contents SWL-3000AP Series Access Point User’s Guide This Guide is a copyright Table of Contents Appendix Ⅰ Introduction Status Wireless RS-232C RJ-45 Connector Ethernet Power Installation SWL-3000APDA SWL-3300AP SWL-3300APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Enter the Same Essid Channel of two APs in PTP Mode Page Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Management Box Bridge Table and Protocol Management Using AP ManagerProtocol Page Select Enabled Select Protocol Which You Do Not Want NAT Setting Using AP Manager Select Server Tab NAT Setting IP Address Subnet Mask SettingConfirm NAT Setting Confirm NAT Setting Page Page Dhcp Server Setting Using AP Manager Select ServerSelect Empty Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Adsl and Cable Modem Connection Setting Using AP Manager Select on Menu Bar Select on Dialogue BoxSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Encryption Setting Using AP Manager Select Encryption Start Encryption SettingPage Confirm 6440-bit Encryption Setting Confirm Encryption SettingUser Access Control Setting Using AP Manager Deny PassSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Line Setting Scope of Number of Packet Transmitted per SecondSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Communication Page Page AP Basic Setting Using RS-232CCOM Port MagicLANCMDt,p,h Enter Menu Number CMDt,p,h Enter Essid Enter new Essid Max Ascii testAPSetting Selection Enter new Dhcp Client enable, disable disableCMDt,p,h Enter Current Channel Enter new Channel 1-14 CMDt,p,h Enter DhcpCMDt,p,h Enter Subnet Mask Enter new Subnet Mask CMDt,p,h Enter Gateway Address Enter new Gateway AddressSelect Advanced CMDt,p,hPage Select Save and reboot TestAP Load default values Using RS-232CCOM Port All items was set to the default valuesFirmware Upgrade Using RS-232CCOM Port Via serialApfirm Page 1K Xmodem Explanation of Basic Configuration to use AP Manager Appendix ⅠMenu Bar List Box Dialogue Box Button BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page Appendix Ⅱ. Specification GeneralManagement Features Environmental Information We value your feedback