Samsung 152x, 172x manual Unbalanced

Page 42

unbalanced.	Have you adjusted the
	resolution or frequency to the
	monitor?

Adjust the resolution and frequency at the video card.

(Refer to the Preset Display Modes).

The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.

The screen is out of focus or OSD cannot be adjusted.

LED is blinking but no images on the screen.

There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.

There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".

Have you adjusted the resolution or frequency on the monitor?

Is the frequency properly adjusted when checking the Display Timing on the menu?

Have the Windows colors been set properly?

Has the video card been set properly?

Have you installed the monitor driver?

See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.

Adjust the resolution and frequency of the video card.

(Refer to the Preset Display Modes).

Adjust the frequency properly by referring to the video card manual and the Preset Display Modes.

(The maximum frequency per resolution may differ from product to product.)

For Windows ME/XP/2000 : Set the colors properly at the Control Panel, Display, Settings.

Set the video card by referring to the video card manual.

Install the monitor driver according to the Driver Installation Instructions.

Install the monitor driver according to the Driver Installation Instructions.

Check the following items if there is trouble with the monitor.

1.Check if the power cord and the cable are properly connected to the computer.

2.Check if the computer beeps more than 3 times when booting.

(If it does, request an after-service for the main board of the computer.)

3.If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver.

4.Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution.)

5.If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

Note: If problems repeatedly occur, contact an authorized service center.

Image 42

Contents SyncMaster 152x/172x Page Notational Power Use only a properly grounded plug and reoeptaclePlace the monitor on a flat and stable surface InstallationDo not drop the monitor when moving it Set down the monitor carefullyClean Do not spray detergent directly on the monitorDo not place any heavy objects on the monitor Keep all power adaptors apartOther Do not use or store inflammable substances near the monitorKeep power adaptor away from any other heat source Remove and discard vinyl bag from power adaptor before useSub Cable Quick Setup Guide Power Cord Warranty Card Monitor UnpackingSub Cable Quick Setup Guide DVI Cable Option Warranty Card Front ButtonSyncMaster Rear DVI port Connecting Your Monitor Setup-GeneralSyncMaster Using the Stand ConnectingClick Windows ME Driver Installing the Monitor DriverWindows ME Windows XP/2000Page Microsoft Windows XP Operating System Page How to install Click Start , Setting , Control Panel Microsoft Windows NT Operating System Linux Operating SystemPage Step-By-Step Installation MagicTune InstallationOverview- What is MagicTune System RequirementsPage Page Start MagicTune Click Support Click Help Site On Screen Display OSD SyncMaster Brightness BrightnessNtrast ContrastImage Lock Image Lock FineImage Lock Coarse Position PositionReset Reset Geometry ResetReset Color Reset Color Control Color TemperatureColor Temperature Color TontrolHalftone HalftoneLanguage LanguageMenu Position Menu PositionH-PositionMenu PositionV-Position Menu Display Time Display ModeDisplay Mode Menu Display TimeOSD Lock / Unlock Auto AdjustmentAuto Adjustment OSD Lock/UnlockMagic Bright Magic BrightNo images on the screen. I cannot turn on the monitor Check Signal Cable onCan you see Video mode not supported on the screen? Can you see No ConnectionUnbalanced Symptom Check List Solutions Screen suddenly has become unbalanced Question Self-Test Feature Check Judging the monitors working condition General LCD PanelPage Horizontal KHz ~ 81 kHz Vertical 56 Hz ~ 75 Hz Dot Acceptable PowerSaver EPA/ENERGYGreen Horizontal Frequency Preset Timing ModesPreset Timing Modes Vertical FrequencyHorizontal Service BrazilEspaña United KingdomNETHERLANDS/BELGIUM/LUXEMBOURG Dot Pitch ResolutionTerms Interlace and Non-Interlace MethodsUser Information RegulatoryFCC Information User Instructions IC Compliance NoticeEuropean NoticeEurope Only Why do we have environmentally-labelled monitors?MPR II Compliance PCT NoticeLead What does labelling involve?Environmental Requirements CadmiumWhy do we have environmentally labelled computers? MercuryCFCs freons TCO Development Environmental requirements Flame retardantsEmissions ErgonomicsEnergy EcologyTCO03 Recycling Information TCO03 applied model only Natural Color Software Program How to install the Natural Color softwareHow to delete the Natural Color software program Natural ColorFor Better Display For Better DisplayAuthority