Samsung M8-DVR manual Command Block Register Descriptions

Page 45

6.3.3.2Device Control Register (ex. 3F6h)

The bits in this register are as follows:

7

6

5

4

3

2

1

0

HOB

R

R

R

R

SRST

nIEN

0

 

 

 

 

 

 

 

 

HOB is the High Order Byte used for host to access the Extended Registers in the 48-bit LBA mode

SRST is the host software reset bit. The drive is held reset when this bit is set. If two disk drives are daisy chained on the interface, this bit resets both simultaneously.

nIEN is the enable bit for the drive interrupt to the host. When nIEN=0, and the drive is selected, INTRQ is enabled through a tri-state buffer. When nIEN=1, or the drive is not selected, the INTRQ signal is in a high impedance state.

R is for reserved

6.3.4Command Block Register Descriptions

6.3.4.1Data Register (Ex. 1F0h)

This 16-bit register is used to transfer data blocks between the device data buffer and the host. It is also the register through which sector information is transferred on a Format Track command. Data transfers may be either PIO or DMA.

6.3.4.2Features Register and Feature Extended Register (Ex. 1F1h)

This register is command specific and used to enable and disable features of the interface (e.g., by the Set Features command to enable and disable caching). The Feature Extended Register contains the upper byte of the Feature Register.

6.3.4.3Sector Number Register and Sector Number Extended Register (Ex. 1F3h)

In CHS mode this register contains the starting sector number for any disk data access for the subsequent command. The sector number is from 1 to the maximum number of sectors per track. In LBA mode this register contains bits 0-7 of the LBA. The Sector Number Extended Register is for bits 25-31 of the 48-bit LBA. See the command descriptions for the contents of the register at command completion (whether successful or unsuccessful).

6.3.4.4Error Register (Ex. 1F1h)

This register contains status from the last command executed by the drive or a Diagnostic Code.

At the completion of any command except Execute Drive Diagnostic, the contents of this register are valid when ERR=1 in the Status register.

Following a power-on, a reset, or completion of an Execute Drive Diagnostic command, this register contains a Diagnostic Code.

 

7

6

5

4

 

3

2

1

0

 

 

#

#

#

#

 

#

ABRT

#

#

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spinpoint M8-DVR Disti Product Manual REV 2.0

 

 

 

39

 

Image 45
Contents M8-DVR Product Manual Page Table of Contents Smart APM Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Scope User DefinitionManual Organization Reference SataIntroduction DescriptionKey Features Hardware Requirements Standards and RegulationsSpecification Summary SpecificationsLogical Configurations Physical SpecificationsPhysical Specifications Physical dimensionsPerformance Specifications Power consumption Power consumptionPower Requirements RatedEnvironmental Specifications Environmental SpecificationsLinear Shock 1/2 sine pulse Rotational Shock1Measurement Position Annualized Failure Rate AFR Reliability SpecificationsSpace Requirements InstallationMounting Unpacking InstructionsOrientation Mounting DimensionsCable Connectors VentilationSata Connectivity Computer mainboard Serial ATA Management PowerHDD Power, Sata Interface, and Factory Jumper Connector SATA-Bus Interface ConnectorPin Locations on the Drive Pcba DC Power Connector and SATA-Bus Interface Cable Connections Drive InstallationBase Casting Assembly Head / Disk Assembly HDADC Spindle Motor Assembly Disk Drive OperationCoverAssembly Head Stack Assembly Disk Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDigital Signal Process and Interface Controller Drive ElectronicsDisk Controller DDR Buffer Control Block Host Interface Control BlockDisk Control Block Disk Ldpc Control BlockFrequency Synthesizer Read/Write IC Power ManagementTime Base Generator Automatic Gain ControlAnalog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass FilterServo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Automatic Defect Allocation Defect ManagementSmart 6 APMSata Terminology Sata II InterfaceSpinpoint M8-DVR Disti Product Manual REV Signal Descriptions Physical Interface Signal Summary2 I/O Register Address When read When writtenControl Block Register Descriptions RegistersCommand Block Register Descriptions Device Register Ex F6h Command Register Ex F7hStatus Register Ex F7h Device Activity Signal Sata II Feature SETStaggered Spin-up Disable Control Auto-Activate in DMA Setup FISPhy. Event Counters Sata Power Management Software Settings PreservationATA Command Descriptions Command TableCommand Code Parameters Smart Check Power Mode E5h Command DescriptionsDevice Configuration Overlay B1h Download Micro Code 92hDevice Configuration Identify data structure Word Content Diagnostic Codes Execute Device Diagnostics 90hFlush Cache E7h, EAh extended Format Track 50hIdentify Device information Content Description=the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content DescriptionAutomatic Standby Timer Periods Idle E3hIdle Immediate E1h NOP 00h Initialize Device Parameters 91hRead Buffer E4h Read DMA C8h, 25h extendedRead Multiple Command C4h, 29h extended Read Log Extended 2FhRead Long 22h Read Native Max Address F8h, 27h extended Read Sectors 20h, 24h extendedRead Verify Sectors 40h, 41h extended Recalibrate 10h Security Disable Password F6hSecurity Erase Prepare F3h Security Erase Unit F4hSecurity Erase Unit Password Security Set Password F1hSecurity Set Password data content Security Freeze Lock F5hIdentifier Level Command result Set Features EFhSecurity Unlock F2h Seek 7xh12 Transfer Mode Values 11 Set Features Register Definitions13 Set Max Feature Register Values Set Multiple Mode C6hSet Max Address F9h, 37h extended Sleep E6hSmart disable operations D9h 14 Smart Feature Registers ValuesSmart enable/disable attribute auto-save D2h Smart B0hSmart execute off-line immediate D4h Smart enable operations D8h15 Device Smart Data Structure Smart read data D0hByte 16 Smart Attribute Status Flags Bit Name Description18 Off-line Data Collection Status Values 17 Smart Attribute Data List19 Self-test Execution Status Values Self-test execution status byteSmart read log sector D5h Smart return status DAhSmart write log sector D6h Write Buffer E8h Standby Immediate E0hWrite DMA CAh, 35h extended Write Fpdma Queued 61hWrite Multiple Command C5h, 39h extended Write Long 32hWrite Sectors 30h, 34h extended Spinpoint M8-DVR Disti Product Manual REV Maintenance Maintenance PrecautionsGeneral Information HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair

M8-DVR specifications

The Samsung M8-DVR is an advanced digital video recorder designed to meet the ever-evolving demands of modern surveillance and recording needs. This cutting-edge device combines state-of-the-art technology with user-friendly features, making it a reliable choice for both residential and commercial applications.

At the core of the M8-DVR’s design is its high-definition recording capability. The device supports various resolutions, including Full HD 1080p, ensuring that all captured footage is crystal clear. This clarity is crucial for identifying details, whether for security purposes or monitoring activities around the clock. It can accommodate multiple camera inputs, allowing users to expand their surveillance network seamlessly.

One of the standout features of the M8-DVR is its remarkable storage capacity. Equipped with advanced hard disk technology, it can store several terabytes of footage, which can be further expanded using additional drives. This means that even with continuous recording, users won’t have to worry about running out of storage quickly. The device also incorporates efficient compression technologies, such as H.265, which allows for reduced file sizes without sacrificing video quality.

In terms of connectivity, the M8-DVR offers various options, including Ethernet ports for network connectivity, USB ports for data transfer, and HDMI output for direct connection to monitors. This versatility allows users to easily stream live footage or review recordings on larger screens. The device supports remote viewing through mobile applications, allowing users to monitor their property from virtually anywhere in real-time.

User experience is further enhanced by an intuitive interface that makes navigation simple and efficient. It includes features like motion detection and alerts, which notify users of any unusual activities. The advanced search function is another highlight, enabling users to quickly locate specific events in their recordings without long hours of scrolling.

The Samsung M8-DVR is also designed with durability in mind. It comes with robust security features to protect against unauthorized access and offers backup options to prevent data loss. With its blend of technology, storage capabilities, and user-friendly design, the Samsung M8-DVR stands out as a comprehensive solution for modern video surveillance needs, making it an essential tool for enhancing security and peace of mind in any environment.