Technicolor - Thomson XRB3059-A operating instructions Controls and displays, Display

Page 23

Controls and displays

05

8 PHONES jack

Use to connect headphones (when connected, there is no sound output from the speakers).

9 STANDBY/ON

Switches the receiver between on and standby.

10 VIDEO INPUT

See Connecting to the front panel video terminal on page 17.

11 USB interface

Connect a USB audio device for playback (see Using the USB interface on page 34).

12 MCACC SETUP MIC jack

Use to connect the supplied microphone.

13MASTER VOLUME dial

14DIMMER

Dims or brightens the display.

15 ANALOG ATT

Attenuates (lowers) the level of an analog input signal to prevent distortion.

16 MIDNIGHT/LOUDNESS

Switches between Midnight and Loudness listening (page 32).

17 SPEAKERS

Use to change the speaker system (page 54) and the speaker impedance setting (page 63).

18 TUNING / STATION

Selects the frequency (page 45) and station presets (page 46) when using the tuner.

19 TUNER EDIT

Press to memorize and name a station for recall (page 46).

20 TONE

Press this button to access the bass and treble controls, which you can then adjust with the MULTI JOG dial (page 32).

21 QUICK SETUP

See Using the Quick Setup on page 8.

22System Setup menu controls

SETUP – Use with the MULTI JOG dial to access the System Setup menu (page 9, page 36, page 58).

RETURN – Press to confirm and exit the current menu.

23SIGNAL SELECT

Use to select an input signal (page 33).

24 SBch PROCESSING

Selects surround back channel processing or the virtual surround back mode (page 31).

25 ACOUSTIC EQ

Press to select an Acoustic Calibration EQ setting (page 30).

English Deutsch Français Italiano Nederlands

Display

1

2

3

4

5

6

7

8

9

10

11

	[ L ]	6
	[ C ]
SP	AB [ R ]
	[Rs]	0
	[SBR]
	[SBL]
	[Ls]	6
		6

4 0 125 25 0 4 K1 3K

12 13	14	15	16	17	18	19	20	21
1 SIGNAL indicators					SB – Depending on the source, this lights
Lights to indicate the type of input signal:					when a signal with surround back channel
AUTO – Lights when AUTO signal select is					encoding is detected.
AUTO – Lights when AUTO signal select is

on.

Español

23

En

Image 23

Contents VSX-816-S/-K Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Voltage selectorVentilation Caution Contents Other connections Other SettingsMaking recordings Controlling the rest of your SystemBefore you start Listening to Surround Sound Minute guideMinute guide Chapter Introduction to home theater02 5 minute guide Using the Quick Setup Switch on the receiver and your TV Quick surround sound setupQuick surround sound setup Chapter Enter Quick surround sound setupOther problems when using the Auto Mcacc Setup Making cable connections Connecting upConnecting up Chapter DVD player Connecting up Connecting a DVD player and TVUse a coaxial digital audio cable for the connection.1 Use an optical cable for the connection.4 Connecting upConnecting the multichannel analog outputs Audio and Video inputs on this receiver.2Use an optical cable to make this connection Connecting up Connecting other audio componentsAbout the WMA9 Pro decoder Use a coaxial digital audio cable for the connection.3 Connecting other video componentsComponent 1 DVD Component 2 TV Component 3 DVR Using the component video jacksConnecting to the front panel video Terminal To improve AM reception Connecting up Connecting antennasUsing external antennas To improve FM receptionSurround speakers Connecting up Connecting the speakersThis receiver Powered Fig. a Hints on speaker placementYou can also refer to the 3-D speaker setup illustration on Overhead view of speaker setupView of 7.1 channel speaker setup ST/DIRECT/AUTO Surr Controls and displaysControls and displays Chapter Front panelDisplay Controls and displaysAuto Surr DigitalVIR.SB DirectNumber buttons and other receiver Component controls Controls and displays Remote controlReceiver Multi Control buttonsComponent control buttons 5TUNE/ST +/- /ENTERTV Control buttons Operating range of remote control Listening in surround sound Listening to your systemListening to your system Chapter Auto playbackListening to your system Using the Advanced surround effectsSetting the effect options Press ‘ADV.SURR’ repeatedly to select a listening modeListening with Acoustic Calibration EQ Listening in stereoUsing Virtual Surround Back VSB Enhancing dialog Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsStart playback of the component you selected in step Choosing the input signalListening to your system Playing other sources Use the input select buttons.1Basic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout MPEG-4 AAC USB playbackCompressed audio compatibility Other compatibility informationSelect the setting you want to adjust System Setup menuSystem Setup menu Chapter Surround back speaker settingSelect ‘Manual MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Speaker Distance Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySelect ‘EQ Auto Setting’ from the Manual Mcacc setup menu Wait for the EQ Auto Setting to finishSelect ‘OK’ to copy and confirm Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘EQ Data Copy’ from the Manual Mcacc setup menuChecking your Acoustic Calibration EQ settings Manual speaker setupManual SP Setup menu Speaker SettingChannel Level Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Crossover NetworkSpeaker Distance Listening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationChanging the frequency step Using the tuner Saving station presetsNaming station presets Listening to station presetsMaking an audio or a video recording Making recordingsMaking recordings Chapter Operating other Pioneer components Setting the remote to control other componentsControlling the rest of your system Controlling the rest of your system ChapterDirect function Erasing all of the remote control presetsControlling the rest of your system Select Confirming preset codesControls for TVs InputDisc AudioGuide ReturnREC Stop RECSHIFT+ + CH Enter GuideCH + SubtitleOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsBi-amping your front speakers Bi-wiring your speakersOther connections Using this receiver with a Pioneer plasma display Connecting additional amplifiersFront panel display shows SR+ on or OFF Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuDynamic Range Control Setup Other SettingsOther Setup menu SR+ Setup for Pioneer plasma displays Dual Mono SetupLFE Attenuator Setup Additional information Chapter TroubleshootingAdditional information Large or Small is Additional informationPress Setup to confirm Resetting the main unitSwitching the speaker impedance Changing the TV format settingAdditional information Specifications Furnished Parts Power cord cautionCleaning the unit MiscellaneousPioneer Corporation