Technicolor - Thomson XRB3059-A Resetting the main unit, Switching the speaker impedance

Page 63

Additional information

Problem

Remedy

The SR cable is connected, but

• Reinsert the SR cable, making sure it’s connected to the right jack (see Using this

the connected components

receiver with a Pioneer plasma display on page 56).

can’t be operated with the

• Make sure an analog connection has been made between the units.

remote.

• This feature only works with Pioneer products.

 

 

The display is dark or off.

• Press DIMMER on the control repeatedly to return to the default.

 

 

The System Setup screen

• When the receiver is in standby, switch to BURST.OFF by holding down ACOUSTIC

doesn't appear.

EQ (front panel) and pressing STANDBY/ON (the current setting is displayed).

 

 

USB mass storage device is

• Try switching the receiver off, then on again.

not recognized by the receiver.

• Make sure you have completely inserted the USB connector to this receiver.

 

• Check that the memory format is FAT16 or FAT32 (FAT12, NTFS and HFS are not

 

supported).

 

• USB devices with an internal USB hub are not supported.

 

 

USB ERR3 shows in the display

• If this message continues to appear after going through all the checks in

when connecting a USB

Important on page 34 of USB playback, take the unit to your nearest Pioneer

device.

authorized service center or your dealer for servicing.

 

 

Can’t play audio files.

• The WMA or MPEG-4 AAC files were recorded using DRM (digital rights

 

management), or the bit rate/sampling rate is not compatible (see Compressed

 

audio compatibility on page 35). This is not a malfunction.

 

 

14

English Deutsch Français Italiano

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the TONE button,

press and hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press ENTER.

OK? shows in the display.

4Press SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory settings.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating.

•With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button.

Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

Changing the TV format setting

If the System Setup menu is not displayed correctly, it may be that the TV system is set incorrectly for your country or region.

•With the receiver in standby, press STANDBY/ON while holding down the SIGNAL SELECT button.

The display shows the new setting (PAL or NTSC).

Nederlands Español

63

En

Page 62 Page 64
Image 63
Page 62 Page 64
Contents VSX-816-S/-K Risk of Electric Shock Do not Open Important the Moulded PlugVoltage selector Ventilation CautionOperating Environment Contents Other connections Other SettingsMaking recordings Controlling the rest of your SystemBefore you start Listening to Surround Sound Minute guideMinute guide Chapter Introduction to home theater02 5 minute guide Using the Quick Setup Quick surround sound setup Quick surround sound setup ChapterSwitch on the receiver and your TV Enter Quick surround sound setupOther problems when using the Auto Mcacc Setup Connecting up Connecting up ChapterMaking cable connections Connecting up Connecting a DVD player and TV Use a coaxial digital audio cable for the connection.1DVD player Use an optical cable for the connection.4 Connecting upConnecting the multichannel analog outputs Audio and Video inputs on this receiver.2Connecting up Connecting other audio components About the WMA9 Pro decoderUse an optical cable to make this connection Use a coaxial digital audio cable for the connection.3 Connecting other video componentsUsing the component video jacks Connecting to the front panel video TerminalComponent 1 DVD Component 2 TV Component 3 DVR To improve AM reception Connecting up Connecting antennasUsing external antennas To improve FM receptionConnecting up Connecting the speakers This receiver PoweredSurround speakers Fig. a Hints on speaker placementOverhead view of speaker setup View of 7.1 channel speaker setupYou can also refer to the 3-D speaker setup illustration on ST/DIRECT/AUTO Surr Controls and displaysControls and displays Chapter Front panelDisplay Controls and displaysAuto Surr DigitalVIR.SB DirectNumber buttons and other receiver Component controls Controls and displays Remote controlReceiver Multi Control buttons5TUNE/ST +/- /ENTER TV Control buttonsComponent control buttons Operating range of remote control Listening in surround sound Listening to your systemListening to your system Chapter Auto playbackListening to your system Using the Advanced surround effectsSetting the effect options Press ‘ADV.SURR’ repeatedly to select a listening modeListening with Acoustic Calibration EQ Listening in stereoUsing Virtual Surround Back VSB Enhancing dialog Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsStart playback of the component you selected in step Choosing the input signalListening to your system Playing other sources Use the input select buttons.1Basic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout MPEG-4 AAC USB playbackCompressed audio compatibility Other compatibility informationSelect the setting you want to adjust System Setup menuSystem Setup menu Chapter Surround back speaker settingSelect ‘Manual MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Speaker Distance Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySelect ‘EQ Auto Setting’ from the Manual Mcacc setup menu Wait for the EQ Auto Setting to finishSelect ‘OK’ to copy and confirm Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘EQ Data Copy’ from the Manual Mcacc setup menuChecking your Acoustic Calibration EQ settings Manual speaker setupManual SP Setup menu Speaker SettingChannel Level Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Crossover NetworkSpeaker Distance Listening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationChanging the frequency step Using the tuner Saving station presetsNaming station presets Listening to station presetsMaking recordings Making recordings ChapterMaking an audio or a video recording Operating other Pioneer components Setting the remote to control other componentsControlling the rest of your system Controlling the rest of your system ChapterErasing all of the remote control presets Controlling the rest of your systemDirect function Select Confirming preset codesControls for TVs InputDisc AudioGuide ReturnREC SHIFT+REC Stop + CH Enter GuideCH + SubtitleOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsBi-wiring your speakers Other connectionsBi-amping your front speakers Using this receiver with a Pioneer plasma display Connecting additional amplifiersFront panel display shows SR+ on or OFF Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuOther Settings Other Setup menuDynamic Range Control Setup Dual Mono Setup LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Troubleshooting Additional informationAdditional information Chapter Large or Small is Additional informationPress Setup to confirm Resetting the main unitSwitching the speaker impedance Changing the TV format settingAdditional information Specifications Furnished Parts Power cord cautionCleaning the unit MiscellaneousPioneer Corporation
Top Page Image Contents