Technicolor - Thomson XRB3059-A operating instructions Quick surround sound setup, Enter

Page 10

03Quick surround sound setup

5 Make sure ‘Normal (SB)’ is selected then press ENTER. 1

Try to be as quiet as possible after pressing ENTER. The system outputs a series of test tones to establish the ambient noise level.

6Follow the instructions on-screen.

•Make sure the microphone is connected.

•If you’re using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is turned up.

•See below for notes regarding background noise and other possible interference.

7Wait for the test tones to finish.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

2.Auto MCACC

Now Analyzing

 

 

 

 

 

Environment Check

 

Ambient Noise

[ OK ]

Microphone

[ OK ]

Speaker YES/NO

[ OK ]

 

 

 

:Cancel

If the speaker configuration displayed isn’t

correct, use to select the speaker and to change the setting (and number for surround back). When you’re finished, go to

the next step.

If you see an error message (ERR) in the right side column, there may be a problem with the speaker connection. If selecting RETRY doesn’t fix the problem, turn off the power and check the speaker connections.

9Make sure ‘OK’ is selected, then press

ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for speaker setting, channel level, speaker distance, and Acoustic Calibration EQ.

2.Auto MCACC

Now

Analyzing

 

 

 

 

 

 

 

 

 

Surround

Analyzing

 

 

Speaker

System

[

]

Speaker

Distance

[

]

Channel

Level

[

]

Acoustic

Cal EQ

[

]

:Cancel

Again, try to be as quiet as possible while this is happening. It may take 3 to 8 minutes.

•For correct speaker settings, do not adjust the volume during the test tones.

8Confirm the speaker configuration. The configuration shown on-screen should reflect the actual speakers you have.

2.Auto MCACC

CHECK!

Front

[ YES ]

Center

[ YES ]

Surround

[ YES ]

SB

[

Yx2 ]

SUB W.

[

YES ]

OK :Cancel

10The Auto MCACC Setup has finished! Select ‘SKIP’ to go back to the System Setup menu.

The MCACC indicator on the front panel will light to show the setup is complete.

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the System

Setup menu (starting on page 36).2

You can also choose to view the settings by selecting individual parameters from the Analyzed Data Check screen:

Note

1If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Surround back speaker setting on page 36 and make sure to connect your speakers as necessary before continuing.

2• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will end up with different size settings. You can correct the setting manually using the Speaker Setting on page 42.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

10

En

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VSX-816-S/-K Important the Moulded Plug Risk of Electric Shock Do not OpenVentilation Caution Voltage selectorOperating Environment Contents Controlling the rest of your System Other SettingsMaking recordings Other connectionsBefore you start Introduction to home theater Minute guideMinute guide Chapter Listening to Surround Sound02 5 minute guide Using the Quick Setup Quick surround sound setup Chapter Quick surround sound setupSwitch on the receiver and your TV Quick surround sound setup EnterOther problems when using the Auto Mcacc Setup Connecting up Chapter Connecting upMaking cable connections Use a coaxial digital audio cable for the connection.1 Connecting up Connecting a DVD player and TVDVD player Audio and Video inputs on this receiver.2 Connecting upConnecting the multichannel analog outputs Use an optical cable for the connection.4About the WMA9 Pro decoder Connecting up Connecting other audio componentsUse an optical cable to make this connection Connecting other video components Use a coaxial digital audio cable for the connection.3Connecting to the front panel video Terminal Using the component video jacksComponent 1 DVD Component 2 TV Component 3 DVR To improve FM reception Connecting up Connecting antennasUsing external antennas To improve AM receptionThis receiver Powered Connecting up Connecting the speakersSurround speakers Hints on speaker placement Fig. aView of 7.1 channel speaker setup Overhead view of speaker setupYou can also refer to the 3-D speaker setup illustration on Front panel Controls and displaysControls and displays Chapter ST/DIRECT/AUTO SurrControls and displays DisplayDirect DigitalVIR.SB Auto SurrMulti Control buttons Controls and displays Remote controlReceiver Number buttons and other receiver Component controlsTV Control buttons 5TUNE/ST +/- /ENTERComponent control buttons Operating range of remote control Auto playback Listening to your systemListening to your system Chapter Listening in surround soundPress ‘ADV.SURR’ repeatedly to select a listening mode Using the Advanced surround effectsSetting the effect options Listening to your systemListening in stereo Listening with Acoustic Calibration EQUsing Virtual Surround Back VSB Using the tone controls Using Midnight and LoudnessUsing the Sound Retriever Enhancing dialogUse the input select buttons.1 Choosing the input signalListening to your system Playing other sources Start playback of the component you selected in stepUSB playback Chapter Using the USB interfaceUSB playback Basic playback controlsOther compatibility information USB playbackCompressed audio compatibility About MPEG-4 AACSurround back speaker setting System Setup menuSystem Setup menu Chapter Select the setting you want to adjustSelect the surround back speaker setting System Setup menuManual Mcacc speaker setup Select ‘Manual MCACC’ from the System Setup menuFine Channel Level Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceWait for the EQ Auto Setting to finish Setting the Acoustic Calibration EQ automaticallySelect ‘EQ Auto Setting’ from the Manual Mcacc setup menu Acoustic Calibration EQSelect ‘EQ Data Copy’ from the Manual Mcacc setup menu Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘OK’ to copy and confirmManual speaker setup Checking your Acoustic Calibration EQ settingsSpeaker Setting Manual SP Setup menuCrossover Network Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Channel LevelSpeaker Distance Tuning directly to a station Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tuner Saving station presetsNaming station presets Changing the frequency stepMaking recordings Chapter Making recordingsMaking an audio or a video recording Controlling the rest of your system Chapter Setting the remote to control other componentsControlling the rest of your system Operating other Pioneer componentsControlling the rest of your system Erasing all of the remote control presetsDirect function Input Confirming preset codesControls for TVs SelectReturn AudioGuide DiscSHIFT+ RECREC Stop Subtitle Enter GuideCH + + CHOther connections Second Zone speaker B setupSwitching the speaker system Other connections ChapterOther connections Bi-wiring your speakersBi-amping your front speakers Connecting additional amplifiers Using this receiver with a Pioneer plasma displayDVD player Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma Front panel display shows SR+ on or OFFInput Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsOther Setup menu Other SettingsDynamic Range Control Setup LFE Attenuator Setup Dual Mono SetupSR+ Setup for Pioneer plasma displays Additional information TroubleshootingAdditional information Chapter Additional information Large or Small isChanging the TV format setting Resetting the main unitSwitching the speaker impedance Press Setup to confirmAdditional information Specifications Miscellaneous Power cord cautionCleaning the unit Furnished PartsPioneer Corporation
Top Page Image Contents