Technicolor - Thomson AV2-S Using the remote control for other equipment, Automatic code search

Page 10

Using the remote control for other equipment

The remote control supplied with your set can be used for other equipment, such as video recorders or DVD players. This page provides information concerning the remote control’s use with these types of equipment.

 

VCR

DVD

VCR

Press the VCR button

 

DVD

 

Press the DVD button

 

On/Standby

On/Standby

 

 

 

MENU

To display the main menu

To display the main menu

 

Vertical scrolling in menus

Vertical scrolling in menus

 

Horizontal scrolling in menus

Horizontal scrolling in menus

OK

To confirm an action

To confirm an action

 

 

EXIT

To close a menu

To close a menu

0-9

To directly access channels or enter

To enter numeric values or select options

 

numeric values

in menus

PR+/PR-

To change channels

 

AV

To select AV input

 

REV

Rewind

Rewind

PLAY

Play

Play

FWD

Fast forward

Fast forward

STOP

Stop

Stop

PAUSE

Pause picture

Pause picture

REC

Record

 

Programming the remote control

Automatic code search

This method can be used to automatically find the most appropriate code for your appliance.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down,

press the standby button until the remote control light comes on. Release the two buttons.

3.Point the remote control at the appliance and press PLAY. Wait until the light stops flashing. If the appliance has not gone into standby mode after five seconds, press the PLAY button again to continue the search for the next set of codes.Repeat this operation until the appliance goes into standby mode. There are

20sets of codes.

4.When the appliance goes into standby mode, press the standbybutton on the right side to switch it on again. Then press the REV button to put it back in standby mode, and if necessary, keep pressing until the appliance goes into standby.

5.Press the STOP button and hold it down until the remote control light goes off.

Note: you can cancel the programming operation at any time by pressing the EXIT button.

Manual programming

This method involves carrying out a manual search for the codes to be used for controlling your other appliances.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down, enter one of the codes relevant to your make of appliance (there is a list of codes at the end of this manual). If the remote control light flashes you have entered the wrong code or it is not possible to program the remote control.

3.Point the remote control at the appliance and press the relevant button (VCR or DVD). Press

thestandby button. If the appliance does not go into standby mode, try another code.

Depending on the year of manufacture and the type of appliance, some functions may not be available. Certain codes may cover more functions than others. Test the functions you can control and, if appropriate, try other codes.

Note here the code(s) which work best.

VCR

DVD

When you change the remote control’s batteries, remember to reprogram it.

10

Image 10
Contents Important Safety Instructions Page Page AC Power Supply Cord II Safety TipsBefore Setting Up Important InformationDo not handle the power cord plug with wet hands If problems occur during useWhen using the LCD TV IV CautionSupplied Accessories IntroductionBatteries for the Remote Control Precaution on battery useII Preparation Switching on Getting StartedRemote control TV functions Coloured buttonsAutomatic code search Using the remote control for other equipmentManual programming Channels SET-UP Automatic InstallationInitial set-up Arranging channels in order OrganiserOrganiser Deleting channelsManual Installation Manual channel set-upOperation General operationReturn go back to Overview menu Adjusting the soundSound Broadcast OptionsPhase, Synchronization, V-Position,H-Position Adjusting the picturePicture Preferences Setting the PreferencesSleep timer TV LockChanging the character set temporarily Accessing TeletextNavigation bar NewsflashSubtitles Direct access to subpagesFastext Other Information SocketsConnecting a Computer Connecting headphonesConnecting a video recorder Component signal connectionTroubleshooting Symptoms Possible CausesAntenna Colors fade