Mitsubishi Electronics DX-TL5716U instruction manual Changing installation location, Maintenance

Page 10

Caution and care (continued)

Changing installation location

When moving this unit, be sure to turn off the MAIN switch, make sure that the unit is completely stopped, and then unplug the power cord. When this unit is exposed to excessive shock while being energized, the internal electronic parts or HDD may be damaged. Be careful especially while the power indicator or access indicator is blinking.

Don't move this unit for at least one minute after you turn off the power. Even after the power is turned off, the disc in the HDD keeps rotating by inertia for a while and the head is in an unstable state. This unit in such state is more vulnerable to vibrations and shocks than while being energized. Be careful not to give this unit even a slight shock for at least one minute after turning off the power. Wait at least one minute for the disc to stop, and then you can move the product.

When moving this unit, cover it with shock absorbers to prevent shocks to the inside.

When placing this unit on a floor, lay it gently on a soft mat or cloth.

Maintenance

Gently wipe dirt off the cabinet with a soft cloth.

When dirt persists, clean it off using a cloth soaked in water-diluted neutral detergent and wrung well and then wipe dry.

When using a chemical cleaning cloth, follow its instructions.

Don't use solvent such as benzene and thinner. Otherwise the surface of the product may deteriorate or the coating may come off.

Notes for constructing a surveillance system using this unit

This unit can be controlled by external devices via the external connector, RS-232C connector, or LAN connector. In addition, external devices can be controlled via the external connector, RS422/485 connector, or RS-232C connector. These functions allow this unit to flexibly support an advanced security system. However, depending on the settings of this unit or connection or combination with external devices, this unit or externally connected devices may operate wrongly, causing adverse effects on the entire surveillance system.

When constructing a surveillance system using this unit, you are recommended to check its operation by connecting or combining it with other devices in advance.

Don't use the alarm function of this unit for the purpose of making serious decisions or for applications involving human lives.

When this unit becomes unable to recognize an external device in recording because of a power failure, voltage drop, or other failure, the recording point may move to the HDD inside this unit or other HDD. To prevent such symptom, it is recommended to use an uninterrupted power supply or other similar device.

When you unplug the power cord or turn off the breaker during recording, the HDD may be broken or recorded data may become unable to be played back. When you turn on and off the breaker every day, program the timer recording to be performed while the breaker is on and don't turn off the breaker during the recording.

When the user or any third party uses external devices wrongly, or external devices are affected by electric noise or they are damaged or repaired, the saved data may be lost. Mitsubishi doesn't take any responsibility for damages related to such data loss.

By connecting external HDDs to this unit, you can expand the memory or use them as a copy device. However, when you perform recording, playback, or copy at a high rate using this unit, recording or playback data dropout or other failure may occur depending on the connected device because of slow data transfer or slow response. Be sure to check for such failure before starting the practical operation of the unit.

Don't use the function to control the powers of external devices using the bus power of this unit.

External devices you want to use may not be suitable for the intended application of this unit. For details, you are recommended to contact your Mitsubishi dealer.

When connecting external devices, be sure to secure the connected cables using the supplied clamp bands. When the cables are disconnected or not connected firmly, the system may become unstable or images may not be recorded.

Don't disconnect the cables while this unit is running. Otherwise a failure may be caused.

6

Image 10
Contents DX-TL5716U Page Avertissement Important safeguards Safety Check Damage requiring ServiceReplacement Parts ServicingBefore use / Contents Unplug the Power Cord During a Long Absence About the hard disk drive HDD Installation location and handling Precautions for rack-mountingChanging installation location MaintenanceFor important recordings About DVD/CD discsSupplied power cord Maintenance of DVD drive laser pickupRecording time and product warranty CopyrightNetwork DisclaimerOpen source software MPEG-4 patentSoftware License Agreement Adjusting the built-in clock Press the Pause button to pause playback Playing back recorded imagesPress the Play button on the front panel Still image playbackChanging the screen mode to display images from cameras Press the 4-split buttonChanging the screen mode using the mouse single screen mode Changing the screen mode using the mouse split screen modeSearching for the desired image Press Button to start playbackSpecifying the search time using the calendar Displaying Search menu using the mouse4 5 6 7 8 Copying recorded images Copying images registered in the alarm list Displaying Copy menu using the mouseBackup Copying data by specifying the copy range