JVC BC-D2300U manual Rear panel connectors, Specifications, Installing the power cable hook, Whd

OTHERS

Rear panel connectors

Names	Functions	Types	Remarks
SDI IN	SD digital serial signal input	BNC
SDI OUT	Active through output	BNC
REF	External sync input	BNC
REF	Loop-through	BNC
HD SERIAL OUT 1	HD digital serial signal output	BNC
HD SERIAL OUT 2	Same as above	BNC
HD SERIAL OUT 3	Same as above	BNC
CVBS	Analog composite input	BNC	The optional BC-D231 is required.
Y	Analog component Y input	BNC
Pr	Analog component Pr input	BNC
Pb	Analog component Pb input	BNC
ALARM	[ALARM] connector/RS-232C	D-SUB	9-pin male, inch screw
REMOTE-IN	Remote control input	D-SUB	9-pin female, mm screw
REMOTE-OUT	Remote control bridge	D-SUB	9-pin female, mm screw

Specifications

5Input signal
Video and audio	: SD digital serial signal (SMPTE259M)	1 line
	0.8 Vp-p, 75 ohms unbalanced, active-through
	Bit rate: 270 Mbps
	Embedded audio signal: 4 ch, sampling frequency of 48 kHz
Sync signals	: Sync signal, 75 ohms unbalanced, loop through ....	1 line
	B.B: 0.45 Vp-p (NTSC)
	HD-SYNC: Positive and negative bipolarity tri-sync signal of 600 mVp-p ± 300 mVp-p
5Output signal
Video and audio	: HD digital serial signal
	(SMPTE292M)	3 lines
	0.8 Vp-p, 75 ohms unbalanced
	Bit rate: 1.485/1.001 (1.483516) Gbps, 59.94 Hz
	Effective scanning lines: 1080 lines (1080I), 720 line (720P)
	Embedded audio signal: 4 ch, sampling frequency of 48 kHz
5Quantization
Video resolution	: 10 bits
Audio resolution	: 20 bits
5Signal delay amount
Video system	: 1 frame or 1 frame - 90H, the shortest delay setting not available
Audio system	: The same delay as the video delay time, can be adjusted by ±30 msec.
5Conversion mode	: Three types (4:3 material, letter box material, squeezed material)
5Power supply	: AC 120 V, 50 Hz/60 Hz

REMOTE-IN, REMOTE-OUT terminal pin assignment

5 1

96

Note:

●For the REMOTE connection, use a straight cable which contains twisted paired lines for the signals of TxA and TxB, RxA and RxB.

Pin	Signal	I/O	Contents	Remarks
number	name
1	NC	—	Unconnected
2	TxA	O	Transmission A	RS-485
3	RxB	I	Reception B	RS-485
4	SG	—	Signal ground
5	NC	—	Unconnected
6	SG	—	Signal ground
7	TxB	O	Transmission B	RS-485
8	RxA	I	Reception A	RS-485
9	NC	—	Unconnected

5Power consumption	: 35 W
5External dimensions
(WHD)	: 430 mm x 489 mm x 50 mm
	(16-15/16" x 19-5/16" x 2") (excluding fan motor and connectors)
5Weight	: 6.2 kg (13.7 lbs.)
5Using environment
Installation place	: In a room (install on a table or a rack)
Allowable operating
temperature	: 10˚C to 40˚C (50˚F to 104˚F)
Allowable operating
humidity	: 30%RH to 80%RH (with no condensation)
Allowable storage
temperature	: –20˚C to 60˚C (–4˚F to 140˚F)

5Provided accessories and

options	: Warranty card	x 1
	Instruction manual	x 1
	Service center list	x 1
	Power cable (2.5 m)	x 1
	Rack mount bracket	x 2

Installing the power cable hook

1.Before connecting the power cable, install the supplied hook as shown on the left.

2.After connecting the power cable, lower the hook to secure the power cable in place.

Hook

Screw (M4)	x 4
Screw (M5)	x 4
Hook (for power cable)	x 1

18 19