Mitsubishi Electronics LT-46246 Indicators Symptom Remarks, NetCommand IR Control Symptom Remarks

Page 88

88Appendices

Appendix F: Troubleshooting, continued

Indicators

 

Symptom

Remarks

1.

STATUS indicator light is a steady red.

Room temperature has exceeded proper levels. Cool the

 

 

 

room.

 

 

• The TV has overheated. Clear blocked air vents and ensure at

 

 

 

least four inches of clearance on all sides of the TV.

 

 

 

 

2.

STATUS indicator light is a steady/flashing

Unplug set from AC power. Plug back in and wait one minute

 

red.

 

for blinking to stop.

 

 

• Press SYSTEM RESET button and wait for blinking to stop.

 

 

• If blinking continues, service is required. Contact your dealer

 

 

 

or a Mitsubishi Authorized Service Center to arrange for a

 

 

 

service evaluation. Listings of Mitsubishi Authorized Service

 

 

 

locations can be obtained from our web site, www.mitsubi-

 

 

 

shi-tv.com or by calling 1-800-332-2119.

 

 

 

 

NetCommand IR Control

Symptom

Remarks

 

 

 

1.

Cannot see the menu from the A/V Receiver.

• A/V Receiver Set Up for Audio-Only Switching

 

 

The A/V Receiver is not connected to any video input of

 

 

the TV. To check the A/V Receiver menu, temporarily plug

 

 

into an unused input of the TV, such as Input 3. Exit the

 

 

Auto Input Sensing screen and select Input 3 from the Input

 

 

Selection menu. Press MENU.

 

 

• A/V Receiver Set Up for Audio and Video Switching over HDMI

 

 

Use the MENU key on the A/V receiver’s remote control.

 

 

• A/V Receiver with NetCommand for HDMI.

 

 

Press INPUT to open the Input Selection menu. Highlight

 

 

the A/V receiver icon and press MENU.

2.

NetCommand unable to learn specific device

• A/V Device does not use IR format for remote control

 

keys.

signal. ITT and RF formats cannot be learned.

 

 

• Room lighting may affect the signal. Have the remotes very

 

 

close (6 inches or less) to the TV during Learning.

 

 

• If learning a Mitsubishi remote control, make sure slide

 

 

switch is not set to TV position.

 

 

• Some, but not all, device key functions can be learned by

 

 

NetCommand. For example, POWER and PLAY may be

 

 

learned, but other functions may not.

 

 

• The signal from the remote control may not be strong

 

 

enough. Insert fresh batteries and try Learning again.

 

 

 

Image 88
Contents LT-40148, LT-46148, LT-52148 LT-46246, LT-52246Refer Servicing to Qualified Service Personnel For Your RecordsContents Replacement Parts Outdoor Antenna GroundingInstallation Notes Cleaning Recommendations TV Guide Daily Access RequirementsIf Your TV Gets Damaged Disposal of Your TVPackage Contents Special Features of Your TVTV Control Panel Convenience Inputs GalleryPlayerTV Guide Daily Interactive Program Guide System Convenience Inputs Swivelling StandFront-Panel Indicators Power IndicatorStatus Indicator LED Color TV Condition Additional InformationTV Main Panel IR NetCommand Output/External Controller Input Hdmi Inputs High-Definition Multimedia InterfaceRS-232C Selecting Audio Output Type, 246 Series TVsStand Removal Stand-Removal ProcedureTV Back Cover Protective Sheet Guidelines for Setting Up and Using Your New Widescreen TV Installing the Remote Control BatteriesWhen You First Power On the TV Getting StartedAdditional TV Setup TV CleaningTV Operation AssistanceInitial TV Setup Setting Up TV InputsWhen You First Connect a Device Memorizing ChannelsAuto Input Sensing for CEC-Enabled Devices Setup ProcedureAuto Input/Auto Output Sensing Screens ReceiverControlling A/V Receiver Sound Volume With a Standard TV SetupWith NetCommand IR Control With NetCommand for Hdmi CEC-Enabled Hdmi A/V ReceiverSource device connected directly to the TV Connecting a Computer to the TV Computer Video Connection Audio Video OutputUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsUsing a CableCARD Installing a CableCARDSeries TVs CableCARD MenuInstalling the Cable Tie Before You BeginCable Management Cable RoutingCable service or Hdmi and Audio SignalsCable Box or Satellite Receiver Only Connect MainCables to Input Connect audioAudio Antennas with Separate UHF and VHF Leads Wall Outlet Cable no cable boxAntenna with a Single Lead VCR to a Cable Box Audio & Video VCR to an Antenna or Wall Outlet CableVCR Older Cable Box 26 3. TV ConnectionsReceiver Sound System Using the TV’s Audio Output Receiver with Hdmi OutputTo connect an analog A/V receiver Receiver back panelCamcorder Audio-Only DevicePb Pr Component Video Connection Composite Video ConnectionChoosing a Viewing Source Sleep TimerTV Tips Cancel Remote Control23. F1-F4 For devices under NetCommand control ChannelView Channel Listings Signal Strength Status DisplayAnt 1 TV-PG FAV1Fav Favorite Channels ANT-1TV Signals and Display Formats Signal DefinitionsDVD Image Definitions TV Display Format DefinitionsJpeg Images and the USB Photo Port Viewing Camera Files and GalleryPlayer ImagesJpeg Thumbnail Menu Media Setup Menu Camera Photos and Moving Video as Composite VideoSlide Show Keys for Jpeg Picture Slide ShowRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsFilm Mode Auto, Off Video Mute On, OffGlobal Audio Only On, OffVideo Menu Video Menu OptionsVert Adjustment SharpEdge On, OffDeepField ImagerAudio Menu Audio Menu OptionsANT1/ANT2 SAPCaptions Menu Captions on Analog ChannelsCaptions on Digital Channels Captions Menu OptionsSetup Menu Options Setup Menu1 Enter Setup menu, Edit channel options EditClock TimeManual DateTimer Setup menu, Timer optionsEnergy Fast Power On Mode Low Power Use the External Controller Input Wired IR option seeCreate Getting Started with GalleryPlayerExport Only when Inputs NetCommand Inputs MenuInput Selection menu Selection menuLock Menu Pass CodesParent Menu Other Menu Alternate Rating SystemParent Menu Options U.S.-based rating system TV-YTV-Y7 TV-GOther Menu Options alternate rating system TimeAbout NetCommand IR Control Important Note on NetCommandIR Emitter Placement An IR emitter cable is included with the TVInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepGuide PowerCH/PAGE Operating NetCommand-Controlled Devices Controlling Most Device TypesControlling an A/V Receiver Special Operation MethodsInside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginReceiver Control Automatic Audio Switching Audio Switching SetupAudio Available from TV only Analog Stereo AudioAV Receiver menu to set up audio switching More About Using an Hdmi Connection with this Setup VCRSetup to Control Switching to the TV’s Audio Output AVR menu for audio and video switching with Hdmi outputNetCommand IR Control Device Connected to an A/V Receiver Ated Assign Input column Assign Input1 throughAssign Input5 Open the Inputs Learn menuAppendix a Specifications Width Depth Weight lbsAppendix B Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix C Programming the Remote Control Functions Available for Other A/V DevicesProgramming the Remote Control DVDCABLE/SAT VCR DVD Audio Code VerificationProgramming Codes Make CodeCable Boxes Cable Boxes Make CodeReceivers Make Code Laser Disc PlayersSatellite Receivers Make Code VCRs Make Code ABSDVD Players DVD Players Make CodeAppendices75 Initial Guide Setup Appendix D TV Guide Daily 246 Series TVsMain Guide Screen Elements High-definition ChannelIcon NumberUsing the TV Guide Daily System Setting Up TV Guide DailyNavigating the Guide Modifying the Guide Setup Looking at AdsCustomizing Guide Listings Available OptionsProcedure TV Guide Daily Troubleshooting Tips Symptom RemarksEnabling or Disabling the TV’s NetCommand Hdmi Control Appendix E NetCommand Hdmi Control of CEC DevicesConnecting Hdmi Devices to the TV Appendices81 Resetting Hdmi Control or Removing an Hdmi Device Figure Using NetCommand Hdmi ControlCEC-enabled A/V receiver functions that may be available TV Reset Comparison Guide Appendix F TroubleshootingReset Name When to Use How to Use Resulting Action Service and Customer Support ServiceRead the ON-SCREEN TionsGeneral TV Operation Symptom Remarks TV Channels Symptom RemarksTV Power On/Off Symptom Remarks Picture Symptom RemarksSymptom Remarks Indicators Symptom Remarks NetCommand IR Control Symptom RemarksAppendices89 Trademark and License Information Mitsubishi TV Software To Obtain Warranty Service This Limited Warranty does not CoverWarranty93 Index Index95 MDEAservice@mdea.com System Reset

LT-52246, LT-46246, LT-52148, LT-46148, LT-40148 specifications

Mitsubishi Electronics has consistently been at the forefront of innovation in the electronics sector, and their line of large-screen televisions is no exception. The models LT-40148, LT-46148, LT-52148, LT-46246, and LT-52246 exemplify the blend of advanced technology, impressive performance, and user-friendly features that consumers have come to expect from the brand.

The LT-40148 is a 40-inch television that serves as an excellent choice for smaller living spaces. With a Full HD resolution, this model delivers crisp and vibrant imagery, making every movie night or gaming session an immersive experience. The LT-46148 steps up to a 46-inch screen, offering enhanced viewing for larger rooms. Both models boast Mitsubishi's proprietary color processing technology, which ensures accurate color reproduction for a lifelike viewing experience.

Moving up in size and specifications, the LT-52148 offers a generous 52 inches of display, making it perfect for avid sports fans and movie buffs who crave a cinematic experience at home. This model incorporates Mitsubishi’s unique LED backlighting, which provides enhanced brightness and contrast, illuminating every detail of the picture. The LT-46246 and LT-52246 offer even larger displays at 46 inches and 52 inches, respectively, catering to those who desire both size and exceptional quality.

All five models feature Mitsubishi’s advanced image processing technology, which enhances video smoothness and reduces motion blur during fast-paced scenes. Additionally, these units are equipped with multiple HDMI inputs, making it easier than ever to connect various devices such as gaming consoles and Blu-ray players. The incorporation of built-in speakers and advanced audio technologies ensures that the audio output is just as striking as the visuals.

Moreover, these models also include energy-efficient features that align with modern sustainability efforts, making them a responsible choice for environmentally conscious consumers. In terms of design, Mitsubishi TVs exhibit sleek and stylish aesthetics, able to harmonize with any living space decor.

In summary, Mitsubishi Electronics’ LT-40148, LT-46148, LT-52148, LT-46246, and LT-52246 televisions merge cutting-edge technology with user-friendly features, delivering unparalleled viewing experiences. Whether it's for gaming, movies, or sports, these models surpass expectations, ensuring quality entertainment for any household.