Arcam AVR350 manual Control connections, Connecting to a power supply, Trigger outputs, Mains lead

Page 11
et fk

Control connections

es (REMOTE) OUT. This outputs any remote control signal that is received by one of the two remote control inputs described below (but not signals received from the front-panel). It allows remote control of source components; control is possible by either connecting this output to the devices to be controlled via the 3.5mm IR jack socket (Arcam units only) or by using an IR emitter stuck to the centre of the IR sensor window on the source component (such as a Xantech 283MW mini emitter).

IN LOCAL. Use with a local IR receiver when the AVR350 front panel IR receiver is obstructed.

IN ZONE 2. This allows the AVR350 to be controlled remotely from Zone 2 via infrared remote control (see section ‘Zone 2 connections’ above for further details).

fn RS232 CONTROL Use with control devices having an RS232 serial port (for example, Crestron and AMX touch screen controllers). This connection is also used for upgrading control software. See the sections at the end of this manual for control and programming information.

Trigger outputs

�� �� ��

1/RGB 2/S-VID REMOTE

IN

ZONE

2

12V

OUT

IN

TRIGGER

LOCAL

 

(Z1 & Z2)

 

 

�� �� ��

��

RS232 CONTROL

English

There are three trigger output sockets on the AVR350, each of which is a 3.5mm stereo jack with two contacts, ‘tip’ and ‘ring’. See the tables for technical information on the trigger outputs.

er 12V TRIGGER. This can be used for turning on and off automatically

 

 

 

Connection

Function

Voltage

power amps or source equipment for the main zone and Zone 2. The trigger

Tip

Main zone on

On = 12V, 30mA

lead is wired as shown in the panel.

 

 

Off = 0V

fm VIDEO TRIGGER 1, fl VIDEO TRIGGER 2. These trigger outputs have

 

 

 

 

 

Ring

Zone 2 on

On = 12V, 30mA

different functions depending on how the ‘Video Status’ has been set in the

 

 

Off = 0V

‘General Settings’ menu. See page 10 for full details.

 

 

 

 

 

Sleeve

Ground

0V

 

Connecting to a power supply

fo Power inlet. The AVR350 has a dual voltage power supply that can be switched between 120V and 230V AC. As supplied, this switch should be set correctly for your local supply.

fp GROUND LIFT switch. In complex set-ups that include satellite inputs or radio antennas, grounding the unit may increase the level of background hum or buzz in the loudspeakers. If this occurs, set the ground lift switch to lift the signal ground from the chassis ground.

DO NOT REMOVE the safety earth from the mains cable under any circumstances.

Mains lead

The appliance is normally supplied with a moulded mains plug already fitted to the lead. Check that the plug supplied with the unit fits your supply. If your mains plug is different, consult your Arcam dealer.

If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your Arcam dealer.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with the unit into the power input socket (fo) in the back of the unit. Make sure it is pushed in firmly.

Put the plug on the other end of the cable into your power supply socket and switch the socket on.

AC

INLET

fo

fp

GROUND GROUND LIFT

230

AVR350

11

Image 11
Contents Arcam AVR350 surround sound receiver Safety compliance Safety guidelinesImportant safety instructions Contents Introduction Using this handbookSafety Before you startBefore making connections Using the remote controlCables InstallationPositioning the unit AVR350 rear panelConnection of record decks Audio connectionsAnalogue audio connections Analogue pre-amplifier outputsVideo connections Scart RGB 4-wire connectionSpeaker impedance Connecting loudspeakersUsing spade terminals AM antenna Connecting the AM and FM antennasZone 2 connections FM antennaMains lead Connecting to a power supplyControl connections Trigger outputsNavigating the Set-up menu Configuring the AVR350Set-up mode Set-up Menu Index‘Basic’ Set-up Menus General SettingsBypass the DSP processing Subwoofer SettingsSpeaker Sizes Distance measurements for 5.1 Speaker Delay SettingsSpeaker delay settings Use Channels 6+7 for Level settingsEX Settings Test Tone CycleADV 1 Speaker Eq ADV 2 Video SettingsADV 3 Digital Settings ‘Advanced’ Set-up MenusADV 6 Hdmi Settings Saving Settings and Exit Set-upADV 4 Zone 2 Settings ADV 5 Analogue SettingsCR100 Universal remote control AVR specific keys CR100 Front panel display Switching on/offVolume control Operating your AVR350Zone HeadphonesInput selection Stereo DirectTreble/Bass Remote control buttonsEffects/FX ModeDeleting a preset Using the tunerTuning to a station Storing a presetUsing the Main Menu No centre spreading 20.8 69.8 Phantom centre Using Zone‘Dimension’ is set to 3 for normal use Display Centre spreading EffectDigital multi-channel sources Surround modesFollowing decoding and surround modes are available Mono Two-channel source modesMulti-channel source modes DSP Effects Modes Speaker positioningBi-amping your system Bi-wiring and bi-amping loudspeakersBi-wiring your loudspeakers Before you start important informationFront Right Front Left Speaker Bi-amping using an external power-amplifierTroubleshooting Hum on an analogue input Source switching changes randomly or freezes on one sourceNo Zone 2 audio when playing DTS film Unable to adjust bass and treble controlsIR Remote Codes Command Command codeSystem code Command Command code Scart S-video cable with audio back to processor Scart connectionsScart RGB cable with audio back to processor Radio interference Technical specificationsContinual improvement policy On line registration GuaranteeWorldwide Guarantee
Related manuals
Manual 48 pages 25.89 Kb

AVR350 specifications

The Arcam AVR350 is a high-performance AV receiver that epitomizes the blend of cutting-edge technology and sophisticated design. Known for its exceptional sound quality and advanced features, it caters to audiophiles and home theater enthusiasts alike. The AVR350 stands out with its robust build quality and user-friendly interface, making it an attractive option for those looking to enhance their home entertainment experience.

One of the key features of the Arcam AVR350 is its 7.1-channel amplification, delivering a powerful audio output of 90 watts per channel. This ensures that every sound in your favorite movies, music, or games is reproduced with clarity and depth. The receiver is equipped with advanced Dolby Digital and DTS decoding technologies, which allow it to support high-definition audio formats. This means users can enjoy a truly immersive surround sound experience, whether it’s the booming effects of an action movie or the delicate nuances of a classical performance.

Another standout characteristic of the AVR350 is its digital signal processing. Incorporating sophisticated algorithms, it optimizes audio performance for different environments, ensuring that listeners achieve the best sound quality no matter the size or shape of the room. The inclusion of Arcam's proprietary room EQ technology further enhances the listening experience by adjusting the sound to compensate for the room acoustics, providing a balanced audio output tailored to individual environments.

Connectivity options are comprehensive, with multiple HDMI inputs and outputs supporting high-definition video formats. The AVR350 also supports a variety of other audio-video inputs, including component and composite video connections, as well as analog audio inputs. This versatility makes it easy to integrate with a range of devices, including Blu-ray players, gaming consoles, and streaming devices.

For users keen on multi-room audio solutions, the AVR350 offers the capability to distribute audio to several zones, allowing you to enjoy different music or media in various parts of the home simultaneously. The intuitive on-screen menu simplifies setup and operation, ensuring that users can easily configure their systems according to their preferences.

In summary, the Arcam AVR350 is a well-rounded AV receiver that combines impressive audio performance, advanced decoding technologies, and flexible connectivity options. Its focus on high-quality sound and user convenience makes it an ideal choice for those looking to elevate their home entertainment systems. With the AVR350, enthusiasts can expect a level of audio fidelity that truly transforms the way they experience sound.