![](/images/new-backgrounds/1157228/15722877x1.webp)
|
|
|
|
|
|
|
|
|
|
|
|
| E |
| N |
| 39 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| TIMER RECORDING |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
| SYMPTOM |
|
|
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
| |||||||
| 1. Timer recording won’t work. |
| ● The clock and/or the timer have | Set the clock and/or timer correctly. |
| |||||||||||||
|
|
|
|
|
|
|
| been set incorrectly. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ● The timer is not engaged. | Press TIMER and check to make sure |
| |||||||||
|
|
|
|
|
|
|
|
|
|
| that TIMER appears on the front |
| ||||||
|
|
|
|
|
|
|
|
|
|
| display panel. |
| ||||||
|
|
|
|
|
|
| ● The VCR has not been set up properly. |
| ||||||||||
|
|
|
|
|
|
| ||||||||||||
| 2. |
| ● Timer recording is in progress. | Timer programming can’t be performed |
| |||||||||||||
|
| won’t work. |
|
|
|
|
| when timer recording is in progress. |
| |||||||||
|
|
|
|
|
|
|
|
|
|
| Wait until it finishes. |
| ||||||
|
|
|
|
|
| |||||||||||||
| 3. TIMER and ]on the front |
| ● The timer is engaged but there’s no | Load a cassette with the record safety |
| |||||||||||||
|
| display panel won’t stop blinking. |
|
| cassette loaded. | tab intact, or with the hole covered |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| with adhesive tape. |
| ||||||
|
|
|
|
|
|
| ● The loaded cassette has had its | Press TIMER so that TIMER on the |
| |||||||||
|
|
|
|
|
|
|
| record safety tab removed. | display panel disappears, then eject |
| ||||||||
|
|
|
|
|
|
|
|
|
|
| the cassette and cover its hole with |
| ||||||
|
|
|
|
|
|
|
|
|
|
| adhesive tape, or replace it with a |
| ||||||
|
|
|
|
|
|
|
|
|
|
| cassette on which the safety tab is |
| ||||||
|
|
|
|
|
|
|
|
|
|
| intact. |
| ||||||
|
|
|
|
|
|
| ||||||||||||
| 4. | TIMER blinks for 10 seconds and |
| ● TIMER has been pressed when there | Check the programmed data and re- |
| ||||||||||||
|
| the timer mode is disengaged. |
|
| are no programs in memory, or the | program as necessary, then press |
| |||||||||||
|
|
|
|
|
|
|
| timer record program information | TIMER again. |
| ||||||||
|
|
|
|
|
|
|
| has not been programmed correctly. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| |||||||||||||
| 5. The cassette is automatically |
| ● The end of tape was reached during | The program may not have been |
| |||||||||||||
|
| ejected, the power shuts off and |
|
| timer recording. | recorded in its entirety. Next time |
| |||||||||||
|
| TIMER and ]won’t stop |
|
|
|
|
| make sure you have enough time on |
| |||||||||
|
| blinking. |
|
|
|
|
| the tape to record the entire program. |
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| OTHER PROBLEMS |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
| SYMPTOM |
|
|
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
| |||||||
| 1. | When scanning channels, some of |
|
| ● Those channels have been preset to | If you need the skipped channels, |
| |||||||||||
|
| them are skipped over. |
|
| be skipped. | restore them (☞ pg. 14). |
| |||||||||||
|
|
|
|
|
|
|
| |||||||||||
| 2. | The channel can’t be changed. |
|
| ● Recording is in progress. | Press PAUSE to pause the recording, |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| change channels, then press PLAY to |
| ||||||
|
|
|
|
|
|
|
|
|
|
| resume recording. |
| ||||||
|
|
|
|
|
|
|
| |||||||||||
| 3. | Even though Auto or |
|
| ● The clock setting data received from | Select a different Host Channel during |
| |||||||||||
|
| clock setting has been selected, the |
|
| the Host Channel is incorrect. | the |
| |||||||||||
|
| clock is incorrect. |
|
|
|
|
| (☞ pg. 10), or perform the Manual |
| |||||||||
|
|
|
|
|
|
|
|
|
|
| setting procedure (☞ pg. 11). |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ATTENTION:
This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the VCR does not operate correctly switch its power off and unplug the power cord from the AC supply. Wait for a while and then plug the power back in. Eject and check the condition of the cassette. If everything appears normal resume operating the VCR as usual.