JVC LT-42PM30 manual Troubleshooting

Page 64

Troubleshooting

Refer to the table below to check the condition. If you think that there is a problem, contact the JVC Service Center where you purchased the television.

There is no power

See if the power cord became unplugged.

Check for a blown fuse or circuit breaker or a power outage.

There is no picture or sound

The antenna could be disconnected.

The tuner could be set improperly. See page 58.

The TV station may be having difficulties. Check to see if other stations are working.

Use the HDMI cable with HDMI logo.

If you have a device connected to INPUT-1, INPUT-2 or INPUT-3, you will not be able to hear any audio from the AUDIO OUT on the back of the TV.

You cannot output audio using the DIGITAL AUDIO OPTICAL OUT when you have digital sound from an HDMI device connected to the INPUT-1, INPUT-2 or INPUT-3 connection on the back of the TV.

This TV can accept 480i (Composite / S / HDMI / Component), 480p, 720p, 1080i and 1080p signals. Please check your settings.

Remote control is not operating properly or at all

Check to see that the batteries are still working and properly installed.

Make sure the remote has a clear sight path to the TV.

You may be too far from the TV. You must be within 23 feet (7 meters).

The power turns off by itself

Make sure the set did not become unplugged.

Perhaps the Auto Shut Off is set. See page 41.

Check to see if the Sleep Timer was set. See page 18.

It does not operate correctly

This television is operated by a microprocessor. It is possible that external noise or interference is causing the problem. If the television does not function correctly, remove the electrical plug from the wall outlet and wait a while before inserting it into the wall outlet again and operating the television.

The color quality is poor

Tint and Color may be improperly adjusted. See page 26.

The Video Status mode may be turned to the wrong setting. See page 26.

There are lines across the picture

There could be interference from another electrical appliance, such as a computer, another TV or VCR. Move any such appliances further away from the TV.

The picture is spotted

There could be interference from a high-wattage appliance, like a hairdryer or vacuum, operating nearby. Move the antenna away from the appliance or change to a coaxial cable connection which is less prone to interference.

There are double pictures (ghosts)

A building or passing airplane can reflect the original signal and produce a second, slightly delayed one. Adjust your antenna position.

64

Image 64
Contents Important Note Serial Number Model NumberDo not attempt to service the product yourself Risk of Electric Shock Do not OpenImportant Safety Instructions Important Safety Instructions FCC NoticeTable of Contents Key Features Full or Widescreen ModeLogos & Licenses Package Contents Caring for the frame and stand Caring for the ScreenPackage Contents Tidying the cables Install your TVConnect the stand Disconnecting the stand Photo Viewer Connector TV Basic ControlsFront Panel Side Panel InputTV Basic Controls Rear PanelHdmi Video AudioCompatible Signal Remote Control On Timer / Input / Sleep TimerCH + VOL + Remote Control Full / Regular / Slim / Panorama / Cinema / Full NativeSpeech / Jazz / Classic / Rock / User Standard / Dynamic / Theater / GameSource is V1, V2, V3, V4 Initial Setup Set the modeTurn on the TV Set the language Set time attributeThank you! Setup is now complete Set TV attributeCustomizing Your TV Using the menusDisplay the menu bar Display the desired menu Change or adjust the setting Close the menuCustomizing your TV Video StatusVideo Reset Color TempColor Management Dynamic GammaVideo Input Label Photo ViewerThumbnail View Slide ShowInterval Aspect Closed Caption SettingType Autoscan Tuner ModeAdd Channel Edit Channel When entering the passwordChip When you lock or unlock channels PasswordSet a new password Confirm and setSexual Content Strong Language NR Not RatedGeneral Audience PG Parental Guidance SuggestedCan. Eng Can. FreGuide Auto Adjustment Phase AdjustmentReset PC H-PositionAudio Reset Digital Audio MLSurround Sound StatusPower Indicator IlluminationPlug In Menu Time ZoneLanguage Noise MuteSystem Info Control with HdmiAuto Demo Sync Mode You cannot use PC Smart Input when Control with Hdmi is OnOptical Out PC Smart InputTV Control Mode Pod Control ModeSync Mode Compatible iPod TypesIPod nano IPod mini Enjoy Movies/Music From Your iPod Ready to playIcons of Music Play screen Select Skip to the next/lastITV in Music Play mode Music Play / Video PlayMusic Shuffle Play SettingsShuffle / Repeat / Audiobook On Timer using iPod Error messagesRecharge iPod PC syncHow to set the codes Programming Your RemoteRemote Control Functions Programming Your RemoteSearch Code Function Operates menusSTB mode Programming CodesVCR mode Programming CodesVCR PVR DVD mode Etc Connect an Antenna or Basic Cable Connect a Cable BoxConnect a VCR / DVD Player using Component Video Connect a VCR / DVD Player using Composite VideoConnect an Amplifier using the Digital Audio Optical OUT Connecting Your DevicesConnect an Amplifier or Home Theater System Connect a Digital Source Device Connect a CamcorderConnect a Blu-ray or Hdmi Device Connect a Computer Troubleshooting Picture is slightly cut off when you use 1080p format only No signal or signal can not be displayedPicture is snowy image noise Screen is 80% blackSpecifications subject to change without notice SpecificationsPage Canada Digital Television Transition Notice