NEC V322AVT user manual Installation

Page 7

Installation

English

This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty.

Mounting

DO NOT mount the monitor yourself. Please ask dealer. For proper installation it is strongly recommended to use a trained, qualifi ed technician. Please inspect the location where the unit is to be mounted. Mounting on wall or ceiling is the customer’s responsibility. Not all walls or ceilings are capable of supporting the weight of the unit. Product warranty does not cover damage caused by improper installation, remodelling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty.

DO NOT block ventilated openings with mounting accessories or other accessories.

For NEC Qualified Personnel:

To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location.

Please note the following when mounting on wall or ceiling

When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method.

NEC strongly recommends

 

Unit

No gap

Mounting

 

using size M6 screws

 

 

 

Bracket

 

(10-12 mm + thickness

 

No thread

Washers

 

of bracket and washers in

 

 

 

 

4 mm

 

 

 

under

 

 

 

length). If using screws

 

 

Screw

 

￿ 8.5 mm

 

 

longer than 10-12 mm,

 

 

 

Thickness

 

check the depth of the hole.

 

10-12 mm

 

 

 

 

(Recommended Fasten

 

 

 

of bracket

 

 

 

 

and washers

 

Force: 470 - 635N•cm)

 

 

 

 

 

Screw length should equal

 

NEC recommends mounting

 

depth of hole (10-12 mm) + the

 

interfaces that comply with

 

thickness of mounting bracket

 

UL1678 standard in North

 

and washers. Bracket hole

 

America.

 

should be under ￿ 8.5 mm.

Prior to mounting, inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm.

Refer to the instructions included with the mounting equipment for detailed information.

Make sure there is no gap between the monitor and the bracket.

Orientation

When using the display in the portrait position, the monitor should be rotated clockwise so that the left side is moved to the top and the LED indicator light is on the bottom. This will allow for proper ventilation and will extend the lifetime of the monitor. Improper ventilation may shorten the lifetime of the monitor.

LED Indicator

Mounting location

The ceiling and wall must be strong enough to support the monitor and mounting accessories.

DO NOT install in locations where a door or gate can hit the unit.

DO NOT install in areas where the unit will be subjected to strong vibrations and dust.

DO NOT install near where the main power supply enters the building.

Do not install in where people can easily grab and hang onto the unit or the mounting apparatus.

When mounting in a recessed area, as in a wall, leave at least 4 inches (100 mm) of space between the monitor and the wall for proper ventilation.

Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and mounting apparatus.

Mounting on ceiling

Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time, against earthquakes, unexpected vibrations, and other external forces.

Be sure the unit is mounted to a solid structure within the ceiling, such as a support beam. Secure the monitor using bolts, spring lock washers, washer and nut.

DO NOT mount to areas that have no supporting internal structure. DO NOT use wood screws or anchor screws for mounting. DO NOT mount the unit to trim or to hanging

fi xtures.

Maintenance

Periodically check for loose screws, gaps, distortions, or other problems that may occur with the mounting apparatus. If a problem is detected, please refer to qualifi ed personnel for service.

Regularly check the mounting location for signs of damage or weakness that may occur over time.

English-5

Image 7
Contents MultiSync Advanced Option IndexFCC Information Canadian Department of Communications Compliance StatementEnglish-1 English-2 Important InformationErgonomics Cleaning the LCD PanelCleaning the Cabinet Recommended UseContents Installation Installing and removing optional table top stand Attaching Mounting AccessoriesAttach Mounting Accessories Using Option BoardEnglish-7 Prevent TippingControl Panel Parts Name and FunctionsTerminal Panel Wireless Remote Control Handling the remote control Operating Range for the Remote ControlConnect the supplied power cord SetupDetermine the installation location Install the remote control batteriesAdjust the image See Switch on the power of all the attached external equipmentAdjust the sound Adjust the screen See pages 20English-14 Wiring DiagramConnections Before making connectionsEnglish-15 Connecting a Personal ComputerConnecting a DVD Player or Computer with Hdmi out Connecting a Computer with DisplayPortOFF Power on and OFF ModesBasic Operation English-16Picture Aspect Power IndicatorUsing Power Management Selecting a video sourceInformation OSD Picture ModeAmbient Mode Ambient parameter settingEnglish-19 OSD On-Screen-Display ControlsPicture AdjustEnglish-20 Schedule AudioEnglish-21 OSD PIPEnglish-22 English-23 Multi DisplayEnglish-24 Display ProtectionEnglish-25 Advanced OptionEnglish-26 Recommendations Image Sticking of LCD PanelEnglish-27 English-28 Remote Control FunctionOUT English-29English-30 ConnectionEnglish-31 Function Monitor ID = Code DataOverview Connecting to a NetworkNetwork Setting by Using an Http Browser Controlling the LCD monitor via LAN ControlEnglish-33 Network SettingsPreparation Before Use Handling of the Address for Operation via a BrowserEnglish-34 Alert Mail SettingCONTROL-COOLING FAN = Auto Alert error message listEnglish-35 OSD Display PROTECTION-FANEnglish-36 FeaturesEnglish-37 TroubleshootingProduct Specifications SpecificationsEnglish-38 English-39 Pin AssignmentWeee Mark European Directive 2002/96/EC Manufacturer’s Recycling and Energy InformationDisposing of your old NEC product Energy Saving