NEC NRP-60LCD1 instruction manual Overloading

Page 4

12. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

13. Object and Liquid Entry

Never push objects of any kind into this Monitor through openings as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the Monitor.

14. Servicing

Do not attempt to service this Monitor yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

LCD PROJECTION -MONITOR

Warning

This section must be read carefully and followed by the user prior to the operation of the product.

The manual states important instructions for the user's own safety, and the proper operation of the product.

15. Damage Requiring Service

Unplug the Monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

(a)When the power-supply cord or plug is damaged.

(b)If liquid has been spilled, or objects have fallen into the Monitor.

(c)If the Monitor has been exposed to rain or water.

(d)If the Monitor does not operate normally by following the operating instructions. Adjust only those controllers

that are covered by the operating instructions as an improper adjustment of other controllers may result in damage and will often require extensive work by a qualified technician to restore the Monitor to its normal operation.

(e)If the Monitor has been dropped or the cabinet has been damaged.

(f)When the Monitor exhibits a distinct change in performance - this indicates a need for service.

16. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

17. Safety Check

Upon completion of any service or repair to the Monitor, ask the service technician to perform safety checks to determine that the Monitor is in safe operating condition.

18. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

To reduce the risk of electric shock, do not remove cover or back. No user -serviceable parts inside. Refer to qualified service personnel for repair.

To prevent fire and damages to the product, unplug the unit from the outlet during lightning storm, or when it is left unattended and unused for a long period of time.

Slots and openings in the case are provided for ventilation to ensure reliable operation of the product. Never put in any item-such as a coin, paper, match- through these openings since it may touch dangerous voltage points that could result in fire or shock hazard.

Do not put any object that contains water - such as flowerpot - on the unit. The water may penetrate into the unit, and be a cause of fire or hazardous electric shock.

Do not put on or use the product near water and moisture-such as in a bathroom, washbowl, etc. It may be a cause of fire and electric shock hazards.

Do not let children hang on or climb on the product since it may be a cause of serious injury.

-6-

 

 

 

 

 

 

 

 

 

 

Take the plug when unplugging the unit

 

 

Do not place the product in a lean or

 

 

from the outlet. The cord may cause fire

 

 

unstable place since it may cause a

 

 

or electric shock if damaged.

 

 

serious injury to a person, as well as

 

 

 

 

 

 

 

damage to the product if it falls.

 

 

 

 

 

 

 

 

-7-

Image 4
Contents Special Features LCD Rear Projection MonitorTable of Contents Special FeaturesImportant Safeguards Overloading When Installing the Unit When Moving or Transporting the UnitAir Filter Cleaning Maintenance TipsAir Filter Change Detach the Front Controller Panel Lamp ChangeOpen the Door Reset the Lamp Timer GlossaryLoose Two Screws of the Lamp Exchange the LampConnecting with an External Source Connecting with an side panelVideo Connection Camcorder & Playstation ConnectionDVD Connection Audio ConnectionSurround Speaker Connection Standard Audio ConnectionDigital Satellite Receiver Connection Cable TV Broadcasting ConnectionWatching High Definition Digital Broadcasting External Input Connection SourcePersonal Computer Connection Watching PC on MonitorName of Each Part Front PanelSide and Rear Panel Side PanelParts of the remote controller Rermote Controller GuideBasic Menu Guide Basic MenuTurning on the Monitor Turning off the MonitorWatching VCR Watching DTV or PCWatching VCR Watching DTV or PCScreen Adjustment of DTV or PC Adjusting Screen FormatDisplaying the Menu Selecting an EntryScreen Size Adjustment Screen Mode AdjustmentMaking Picture Adjusting Making AdjustmentWhen Adjusting the Color Exiting Picture AdjustmentSound Adjustment Adjusting the Sound ModeUsing Equalizer Selecting Sound ModeMaking Sound Adjustment When Adjusting to 500HzAdjusting Sound Range Exiting Sound AdjustmentDolby Sound Choosing Dolby Pro LogicSpeaker Sound Adjustment When adjusting the Surround BalanceMaking Adjustment Choosing Sound Choosing on EntryUsing the Memory Feature Time SettingAdjusting to Factory Set Setting Sleep TimerChecking Lamp Time Selecting the On-Screen Language Press the Menu buttonSelect Language Select Utilities by pressing the Up/Down buttonsSpecifications TroubleshootingsSymptoms and Solutions NEC Service Centres ABN 86 001 217