NEC GT1150 user manual Important Information, Precautions, RF Interference, DOC Compliance Notice

Page 4

IMPORTANT INFORMATION

Precautions

Please read this manual carefully before using your NEC GT1150 Pro- jector and keep the manual handy for future reference.

Your serial number is located on the bottom of your GT1150. Record it here:

CAUTION

To turn off main power, be sure to remove the plug from power outlet.

The power outlet socket should be installed as near to the equipment as possible, and should be easily acces- sible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided.The information should be read care- fully to avoid problems.

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Technologies in this manual. Failure to comply with this gov- ernment regulation could void your right to operate this equip- ment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea- sures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio / TV technician for help.

In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-

SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN

BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-

PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-

FIED NEC SERVICE PERSONNEL.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

3. GSGV Acoustic Noise Information Ordinance:

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

• IBM is a registered trademark of International Business Machines Corporation.

• Macintosh and PowerBook are registered trademarks of Apple Com- puter, Inc.

• Other product and company names mentioned in this user's manual may be the trademarks of their respective holders.

E – ii

Image 4
Contents GT1150 GT1150 Declaration of Conformity Precautions Important InformationRF Interference DOC Compliance NoticePrécautions Informations ImportantesDOC avis de conformation Important Safeguards InstallationPower Supply CleaningRemplacement de la lampe Mesures de sécurité importantesAlimentation NettoyageTable of Contents Whats in the Box? IntroductionUser’s manuals Getting to Know Your GT1150 Projector Lens hood Remote sensor Terminal panel LeftControls PC Card slot Lens optionalDepression for foot 4 locations Remote sensor Carrying handle Lamp coverString Carrying the ProjectorRivet Top Features Front Terminal Panel Right Front Terminal Panel Left PC Card ViewerRemote Control Features Undo InfoTest HelpRemote Control Battery Installation Remote Control PrecautionsOperating Range for Wireless Remote Control Using the Remote Control in Wired Operation Remote cable supplied Terminal panel LeftSetting Up Your GT1150 Projector InstallationScreen Size and Projection Distance Lens Shift Adjustable Range Optional Lens Installation Preparation Tools needed for installationBefore installation Lens hood Lens hood capReinstall the lens hood Lens mountSetting up for Double Stacking in Link Mode Master projector Foot Depression for foot Slave projectorStacking the Projectors HookupLink Mode Setting Projector OrientationCeiling Front Projection Ceiling Rear ProjectionDesktop Rear Projection Lect Desktop Rear. See page E-47Connecting the Power Cable and Turn on the Projector Power ON/STAND by buttonIndicators Basic OperationTo turn off the projector About Startup ScreenMenu Language Select screen Set up the projector TestOther adjustments UpDownWhen used in standalone operation Connecting Your VCR Or Laser Disc PlayerConnections VCR or other video equipment TV tuner DVD playerConnecting Your DVD Player with Component Output Audio equipmentConnecting Your PC Or Macintosh Computer RGB signal cable suppliedSupplied MacintoshConnecting an External Monitor Connecting a PC with DVI outputDVI digital input accepts up to the XGA signal DVI cable not suppliedInstallation Instructions Connecting to a Single WorkstationInformation for Reducing Radiation of Electromagnetic Waves When Used with One Switcher ISS-6020/ISS-6020G BNC 5 coaxial cableISS-6020 To Rgbhv output To slot Personal computer To REMOTE1 To audio outputWhen Used with Two or More Switchers 100 Inputs How to make connectionsTo Remote To Remote To Slot Personal Computer SlaveISS-6020 Output to Setting of S8601 Set the DIP switch S8601 of the Switcher as followsWhen used with the Switcher Pin No Remote 1 ConnectorPin Configuration of Optional CTL-6010 Cable External control mode on When used in stand alone operation Pin NoExternal control mode OFF Projector ID= Operating Multiple Projector with Remote ControlProjector ID= Using the PC Control connectors Connection for Double Stacking in Link ModeConnect source equipment to the master projector Master projectorUsing the Menus Using the Magnifying Glass IconOperation General ControlsDefault Basic/Custom Menu items are Customizing Basic/Custom MenuList of Direct Button Combinations Menu tree DVI AnalogMenu Elements Switcher Entry Edit Command Expert mode onlyMenu Descriptions & Functions Source SelectPrev Play Jump Setup View Next Stop Select Delete Volume not available for PC Card ViewerPC Card Viewer Picture not available for PC Card ViewerColor Temperature Lamp ModeImage Options KeystoneColor Matrix available for component video signal only Switcher Gain available only when used with ISS-6020Resolution when Auto Adjust is off White Balance not available for PC Card ViewerProjector Options Commands Sleep TimerMenu Ing to use the volume bar Ume bar on screenOn screen Keystone barSetup Gives normal Jpeg qualityClear Filter Usage Link Mode not available for DVI digital Switcher ControlTools CapturePC Card Files Changing Background LogoHelp Test PatternUsing the PC Card Viewer function Inserting and Ejecting a PC CardInstalling the PC Card Viewer Software Before InstallingInstallation Starting Up the PC Card Viewer Software on your PCOptional Presentation Remote Control Projecting slidesWhen the tool bar is not displayed Auto Play ModeSwitching to Slides Directly from Other Input Modes ExampleCapturing Images Displayed on the Projector Deleting Captured ImagesViewing Digital Images PreparationsUninstalling the PC Card Viewer Software Uninstalling the softwareMaintenance Replacing the LampTo replace the lamp InterlockTo clean the filter Cleaning or Replacing the FilterTo replace the filter Pour remplacer la lampe Contact de sécuritéNettoyage ou remplacement du filtre Pour nettoyer le filtre à airPour remplacer le filtre à air Aspirez le filtre à travers le couvercle de filtreTroubleshooting Power/ Status Light MessagesCommon Problems & Solutions IndicatorWhen using the PC Card Viewer function Supplied software change the image to 1024 768 dots in sizeSpecifications Model Number GT1150Optical ElectricalMechanical Cabinet Dimensions Optional AccessoriesLens center Unit = inch mmRGB Signal Analog YCbCr Signal Video / S-Video Mini D-Sub 15 Pin Connector RGB2Sub Pin Assignments List of Menu Items Available in Link Mode VolumeTiming Chart PC Control Codes Cable ConnectionGravity Stack Function7N8P0112
Related manuals
Manual 75 pages 12.39 Kb

GT1150 specifications

The NEC GT1150 is a high-performance projector designed to meet the demands of various applications in educational, business, and professional environments. Equipped with advanced technologies, it offers exceptional image quality and versatility, making it an ideal choice for presentations and multimedia displays.

One of the standout features of the NEC GT1150 is its brightness. With a remarkable output of 5,000 ANSI lumens, the projector delivers vibrant images even in well-lit rooms. This high brightness level ensures that presentations can be seen clearly in various lighting conditions, lending itself to classrooms, conference rooms, and auditoriums alike.

The resolution of the GT1150 is another key aspect. It supports XGA (1024 x 768), which provides a sharp and detailed image, crucial for displaying text-heavy presentations or intricate visuals. The projector’s contrast ratio enhances this experience, offering deep blacks and bright whites, thus elevating the overall viewing experience for audiences.

In terms of connectivity, the NEC GT1150 is equipped with multiple input options. It includes VGA, composite, and S-Video connections, enabling users to connect a variety of devices such as laptops, document cameras, and DVD players seamlessly. Additionally, the projector features a built-in 10-watt speaker, providing adequate sound output for most presentation settings.

Another interesting characteristic of the GT1150 is its portability. Weighing approximately 7.5 pounds, it is designed with ease of transport in mind, allowing users to set it up quickly in different locations. This mobility makes it a preferred choice for educators and business professionals who need to move between multiple venues regularly.

The GT1150 is also designed with user convenience in mind. It features an intuitive on-screen menu, providing easy access to a range of functions including picture adjustments, source selection, and setup options. This user-friendly interface contributes to a smoother operation, allowing presenters to focus on their content rather than technical difficulties.

Moreover, the NEC GT1150 is built to last, with an expected lamp life of up to 4,000 hours in normal mode, which can stretch to 5,000 hours in eco mode. This longevity reduces maintenance costs and minimizes downtime due to lamp replacements.

In summary, the NEC GT1150 is a versatile and robust projector that excels in delivering high-quality images, a variety of connectivity options, and user-friendly features, making it an excellent choice for a wide array of presentations and multimedia applications. Whether in the classroom or a corporate setting, the GT1150 helps ensure that your content is delivered effectively and efficiently.