Hitachi 32UDX10S, 36UDX10S AV1, AV2, AV3 buttons, Channel selector buttons, Sleep button, Button

Page 23

HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV

AV1, AV2, AV3 buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio/Video mode. (see page 32)

CHANNEL selector buttons

CHANNEL selector buttons are used to set FAMILY FAVORITES, CHANNEL MEMORY, etc.

Enter one, two, or three numbers to select channels. Enter 0 first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the 1 button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up ( ) or down ( ).

You can also use these number buttons to directly access OSD sub-menu s of your choice. While navigating the On-Screen- Display s, you will notice that each sub-menu has a number next to it. For example, the SET UP menu has 9 sub-menu s. Pressing the button while in the SET UP menu will take you directly to the CLOCK SET sub-menu. This makes navigating the menu s faster and easier.

NOTE: The TV may not receive some channels if you are not in the correct SIGNAL SOURCE mode. (see page 38)

SLEEP button

Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use RECALL when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition.

LAST CHANNEL (LAST CH) button

Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)

ANT A 10

LAST CH

ANT A 39

INPUT button

The INPUT button will select between both antenna signals and the three sets of video input jacks each time the button is pressed. If the Picture-in-Picture is on, the INPUT button will select between the three sets of video input jacks and both antenna sources when main channel is chosen with the PIP CH button. If the sub-picture is chosen, the INPUT button will select between the three sets of video input jacks and the ANT A antenna source (ANT B source cannot be displayed as a PIP sub-picture).

ANT A 28

INPUT

S - IN: 1

INPUT

Y - PBPR: 2

INPUT

ANT B 13

INPUT

S - IN: 3

INPUT

C.C. button

Press this button to quickly turn the Closed Caption feature on and off (see page 52 for more information).

HELP button

Press this button when a menu is displayed to view HELP text, which gives a description of the displayed menu. The HELP text will be displayed every time a MENU is displayed, until this button is pressed again.

23

Image 23
Contents 32UDX10S 36UDX10S Safety Points YOU should Know about Your Hitachi Television Important Safety InstructionsPublic Viewing of Copyrighted Material Prevention of Pattern BurnIllustration AccessoriesPartname Partno Remote Control Battery Installation Replacement Viewing HOW to SET UP Your NEW Hitachi Color TVAntenna LocationAntenna Connections to Rear Jack Panel HOOK-UP Cables and ConnectorsFront Panel Controls Input Input Output Front Panel Jacks and ConnectionsMonitor OUT Rear Panel JacksComponent Y-PBPRInput Rear Speaker Terminal Connections Typical FULL-FEATURE SetupTips on Rear Panel Connections Tips on Rear Panel ConnectionsConnecting External Audio Amplifier Connecting External Audio SourcesInput Mode Selection Order Connecting a Stereo VCR or Stereo Laserdisc Player Connecting External Video SourcesVCR or Laserdisc Player Hitachi Model or Similar Model See page 14 for tips on Rear Panel Connections Required Optional Effect Feature Connection Audio System SetupLight Button Genius Remote Control CLU-577TSISatellite SAT HOW to USE the Genius Remote to Control Your TVCable CBL Last Channel Last CH button AV1, AV2, AV3 buttonsChannel selector buttons Sleep buttonExit button VOLUME, Mute buttonAspect button Commercial Skip C.S. buttonPIP button Single Mode PIPPICTURE-IN-PICTURE PIP Single PICTURE-IN-PICTURE Surf Mode PIPPIP Mode button Swap buttonStrobe Freeze Freeze button With PIP onFreeze button With PIP OFF Single FreezeExclusive TV Buttons Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR Precoded VCR ButtonsPrecoded Cable BOX buttons Using the Remote to Control Cable BOX FunctionsOperating the precoded function for your cable box Cable CBL buttonPrecoded Satellite Receiver buttons Using the Remote to Control Satellite Receiver FunctionsOperating the precoded function for your satellite receiver Satellite SAT buttonPrecoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player Precoded AUDIO/VIDEO Buttons Using the Remote to Control Additional AUDIO/VIDEO EquipmentVCR, CABLE, SATELLITE, DVD and AUDIO/VIDEO Codes CLU-577TSI Ultratec OSD Ultratec OSD Menu Language SET UPAntenna or Cable Without Cable BOX Plug & PlaySignal Source Signal SourceAuto Channel SET Channel Memory Channel List Clock SET Rotation Color System Component SETThumb StickChannel ID CustomizeVideo ID Video IDFamily Favorites Menu Family Favorites Operation Stick Parental ControlEvent Prog Auto Link Channel Closed CaptionDisplay ModeW a Y S S H O W F I R S T T I M E T O U R a T P O W E R O N First Time TourVideo Contrast Brightness Color Tint Sharpness ResetNoise Reduction Advanced SettingsColor Temperature Auto ColorBalance AudioBass TrebleInternal Speakers MTS ModeAuto Noise Cancel Perfect VolumeTheater Modes TheaterTechnology SurroundDo not Care of Your Hitachi Color TV Your Remote Control¥ Ignition Noise Reception ProblemsUseful Info Symptoms36UDX10S InputsOutputs 32UDX10SHome Electronics Division HitachiPage Page Page QR48441
Related manuals
Manual 68 pages 7.02 Kb