Hitachi 32HDL51 important safety instructions PRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons

Page 43

HOW TO USE THE REMOTE TO CONTROL

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to pages 48-49 for pre-codes).

1.Turn ON your set-top-box/satellite systems.

2.Aim the remote control at the front of your set-top-box/satellite systems.

3.To switch to set-top-box/satellite (STB) pre-coded mode, use the SOURCE ACCESS buttons (F , E) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your set-top-box/satellite receiver as shown on page 48-49. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your set-top- box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different four digit preset code.

6.The remote will now control your set-top-box/satellite receiver.

NOTES:

1.If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top- box/satellite receiver code has not been precoded into the remote.

2.In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

aPRE-CODED SET-TOP-BOX/SATELLITE RECEIVER buttons

These buttons transmit the chosen pre-coded set-top- box/satellite codes.

bEXCLUSIVE TV buttons

These buttons are for operating the TV.

a

b

A/V NET

GUIDE

b

b

a

a

a

THE REMOTE CONTROL

MY SATELLITE RECEIVER/STB CODE IS:

NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top- box/satellite receiver.

43

Image 43
Contents Operating Guide for 32HDL51 Refer Servicing to Qualified Service Personnel Important Safety InstructionsPublic Viewing of Copyrighted Material Read before operating equipmentAVC and Monitor AccessoriesRemote Batteries Power Cord Monitor IR Mouse Control Subwoofer Cable Cleaning ClothLocation HOW to Setup Your NEW Hitachi LCD TelevisionSecuring to a wall AntennaViewing HOW to SET UP Your NEW Hitachi LCD TelevisionHookup Cables VHF 300-Ohm antenna/UHF antenna When both VHF and UHF antennas are connectedAntenna Connections to Rear Panel Jacks VHF 75-Ohm antenna/CATV Cable TVPhoto Input Front Panel ControlsRemote Control sensor Power button Display Monitor Main Power buttonAVC Power button Power light indicatorRear Panel Jacks RGB Analog Input SUB-POWER buttonUpgrade Card To Power Swivel ConnectorRear Panel of AVC CableCARD SlotConnecting External Video Sources Connecting LCD Display Monitor to AVC BOXBefore Operating External Video Source Connecting a Monaural Audio Source to INPUT1~INPUT5Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player DVI to Hdmi Input Hdmi inputSee page 26 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External Audio Amplifier Connecting External AUDIO/VIDEO DevicesConnecting AV Network Setup Procedure DVD setup example below AV Network Setup WizardSee Remote Control AV NET button usage on pages 31 AUDIO/VIDEO Codes for AV Network not for remote control Rear Panel Connections Tips on Rear Panel Connections Remote Control HOW to USE the Remote to Control Your LCD TV 480i/480P Input RGB Analog Input Aspect Display ModeAspect button RatioGuide button DAY/NIGHT buttonPICTURE-IN-PICTURE button Menu buttonAV NET button RemoteSelect TV Softkeys to learn, press the Select button AV NET Learning WizardPhoto Input Ant B Ant a Inputs buttonIeee Select this menu item to view the chosen picture number JumpRotate SlideshowWhen an IEEE1394 device is connected Info button When an S-VIDEOVideo Last Channel LC button Volume VOL WHEEL, Mute buttonChannel CH WHEEL/CHANNEL Selector buttons Dash buttonPICTURE-IN-PICTURE PIP POP Mode PICTURE-IN-PICTUREPIP button Ntsc PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE Surf Mode PICTURE-IN-PICTURESplit Freeze Main FreezeStrobe Freeze Exclusive TV buttons HOW to USE the Remote To Control Cable BOX FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons These buttons transmit the chosen precoded DVD codes HOW to USE the Remote To Control DVD FunctionsOperating the precoded function for your DVD player Precoded DVD ButtonsPrecoded VCR/PVR Buttons HOW to USE the Remote To Control VCR/PVR FunctionsThese buttons transmit the chosen precoded VCR/PVR codes Operating the precoded function for your Audio component HOW to USE the Remote To Control Additional Audio EquipmentPrecoded Audio Buttons Input Access DVD Brand Audio Brand OSD On-Screen Display Video Audio Aspect Channel Manager Locks Timers Setup SwivelPower Video Picture ModeBack Light Contrast ModeUse this function to adjust the amount of Back Light Contrast selectionColor Management Reset Video SettingsBackground colors Noise Reduction Auto Movie ModeColor Decoding Auto ColorInternal Speakers Auto Noise CancelPerfect Volume AudioDRC Language Digital OutputAuto Aspect AspectAspect Use this function to select the Picture Format Aspect RatioAuto Channel Scan This feature will select Antenna optionsChannel Manager Set The AntennaChannel List Signal MeterLocks Movie Ratings TV Ratings Canadian Ratings Eng Canadian Ratings English ChartCanadian Ratings Frn Set The Clock TimersSet Day/Night Timer Set Sleep TimerPlease Set Clock First Set Event TimerSet Timer Recording Menu Preference SetupMenu Background Image PowerScreen Saver Set The Inputs Video Power SaveGray Black Video 2 Auto LinkSet Black Side Panel AspectSet Closed Caption Caption ModeChannel Set AV Control This feature will select the source of the Monitor OutputSet Monitor Out CableCARD InfoSet Stand-By Mode UpgradesPower Swivel RGB on Screen Display Operation No SYNC. Signal Aspect Setup Power Swivel Move Power Swivel Unlock Brightness ContrastColor Aspect ResetPreset condition EnhancerFor current RGB format are adjusted automatically Auto AdjustPosition Adjusts the phase to correct blurred or unstable images Clock PhaseHorizontal Clock Black Side Real and Normal signals in Standard ModePower Swivel Input LevelDo not Care of Your Hitachi LCD Display Your Remote ControlIgnition Noise Reception ProblemsUseful Info SymptomsTrademark Acknowledgment Plug and PlayAgency Regulatory Information Outputs InputsHitachi Way Chula Vista, CA Home Electronics DivisionDigital Media Division Bass AccessoriesIndex 22-24END User License Agreement for Hitachi DTV Software END User License Agreement for Hitachi DTV Software Page QR62241