Hitachi 32HDL51 HOW to USE the Remote To Control Additional Audio Equipment

Page 46

HOW TO USE THE REMOTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 48-49 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3.To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons (F , E) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 48-49. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

CONTROL

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

a

THE REMOTE

NOTES:

1.If your Audio component cannot be operated after performing the above procedures, your Audio component’s code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP).

5.INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices.

aPRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

bEXCLUSIVE TV Buttons

These buttons are for operating the TV.

b

A/V NET

b

GUIDE

a

a

a

a

MY AUDIO EQUIPMENT CODE IS:

CD

AMP/RCVR

NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes.

2.Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Operating Guide for 32HDL51 Important Safety Instructions Refer Servicing to Qualified Service PersonnelRead before operating equipment Public Viewing of Copyrighted MaterialSubwoofer Cable Cleaning Cloth AccessoriesRemote Batteries Power Cord Monitor IR Mouse Control AVC and MonitorAntenna HOW to Setup Your NEW Hitachi LCD TelevisionSecuring to a wall LocationHOW to SET UP Your NEW Hitachi LCD Television ViewingHookup Cables VHF 75-Ohm antenna/CATV Cable TV When both VHF and UHF antennas are connectedAntenna Connections to Rear Panel Jacks VHF 300-Ohm antenna/UHF antennaFront Panel Controls Photo InputPower light indicator Power button Display Monitor Main Power buttonAVC Power button Remote Control sensorRear Panel Jacks To Power Swivel Connector SUB-POWER buttonUpgrade Card RGB Analog InputCableCARD Slot Rear Panel of AVCConnecting LCD Display Monitor to AVC BOX Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT1~INPUT5 Before Operating External Video SourceConnecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player Hdmi input DVI to Hdmi InputSee page 26 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External AUDIO/VIDEO Devices Connecting External Audio AmplifierConnecting AV Network Setup Procedure DVD setup example below AV Network Setup WizardSee Remote Control AV NET button usage on pages 31 AUDIO/VIDEO Codes for AV Network not for remote control Rear Panel Connections Tips on Rear Panel Connections Remote Control HOW to USE the Remote to Control Your LCD TV Ratio RGB Analog Input Aspect Display ModeAspect button 480i/480P InputMenu button DAY/NIGHT buttonPICTURE-IN-PICTURE button Guide buttonRemote AV NET buttonAV NET Learning Wizard Select TV Softkeys to learn, press the Select buttonPhoto Input Ant B Ant a Inputs buttonIeee Jump Select this menu item to view the chosen picture numberSlideshow RotateWhen an IEEE1394 device is connected Info button When an S-VIDEOVideo Dash button Volume VOL WHEEL, Mute buttonChannel CH WHEEL/CHANNEL Selector buttons Last Channel LC buttonPICTURE-IN-PICTURE PIP POP Mode PICTURE-IN-PICTUREPIP button Surf Mode PICTURE-IN-PICTURE PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE NtscSplit Freeze Main FreezeStrobe Freeze Precoded Cable BOX buttons HOW to USE the Remote To Control Cable BOX FunctionsOperating the precoded function for your cable box Exclusive TV buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons Precoded DVD Buttons HOW to USE the Remote To Control DVD FunctionsOperating the precoded function for your DVD player These buttons transmit the chosen precoded DVD codesPrecoded VCR/PVR Buttons HOW to USE the Remote To Control VCR/PVR FunctionsThese buttons transmit the chosen precoded VCR/PVR codes Operating the precoded function for your Audio component HOW to USE the Remote To Control Additional Audio EquipmentPrecoded Audio Buttons Input Access DVD Brand Audio Brand OSD On-Screen Display Video Audio Aspect Channel Manager Locks Timers Setup SwivelPower Picture Mode VideoContrast selection Contrast ModeUse this function to adjust the amount of Back Light Back LightReset Video Settings Color ManagementAuto Color Noise Reduction Auto Movie ModeColor Decoding Background colorsAudio Auto Noise CancelPerfect Volume Internal SpeakersLanguage Digital Output DRCUse this function to select the Picture Format Aspect Ratio AspectAspect Auto AspectSet The Antenna This feature will select Antenna optionsChannel Manager Auto Channel ScanSignal Meter Channel ListLocks Movie Ratings TV Ratings Canadian Ratings English Chart Canadian Ratings EngCanadian Ratings Frn Timers Set The ClockSet Sleep Timer Set Day/Night TimerSet Event Timer Please Set Clock FirstSet Timer Recording Setup Menu PreferenceMenu Background Image PowerScreen Saver Video Power Save Set The InputsAspect Video 2 Auto LinkSet Black Side Panel Gray BlackSet Closed Caption Caption ModeChannel CableCARD Info This feature will select the source of the Monitor OutputSet Monitor Out Set AV ControlSet Stand-By Mode UpgradesPower Swivel RGB on Screen Display Operation No SYNC. Signal Aspect Setup Power Swivel Move Power Swivel Unlock Brightness ContrastColor Enhancer ResetPreset condition AspectFor current RGB format are adjusted automatically Auto AdjustPosition Adjusts the phase to correct blurred or unstable images Clock PhaseHorizontal Clock Input Level Real and Normal signals in Standard ModePower Swivel Black SideCare of Your Hitachi LCD Display Your Remote Control Do notReception Problems Ignition NoiseSymptoms Useful InfoPlug and Play Trademark AcknowledgmentAgency Regulatory Information Inputs OutputsHome Electronics Division Hitachi Way Chula Vista, CADigital Media Division 22-24 AccessoriesIndex BassEND User License Agreement for Hitachi DTV Software END User License Agreement for Hitachi DTV Software Page QR62241
Top Page Image Contents