Hitachi 42EDT41 user manual Operating Instructions, Turning Power On and Off, Indicating lamp

Page 18

OPERATING INSTRUCTIONS

Indicating lamp

Main power switch

Turning Power On and Off

To turn the monitor power ON, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF button on the remote control.

To turn the monitor power OFF, press the SUB POWER button or the ON/OFF button on the remote control, and then press the main power switch on the monitor main unit to OFF.

ENGLISH

SUB-POWER button

POWER ON/OFF button

During normal use, the main power switch is set in the ON position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.

Indicating lamp

Indicating

Power status

Operating

lamp

 

 

 

 

 

Off

Off

When the main power switch is set

to OFF.

 

 

 

 

 

 

 

When the main power switch is

 

Off

ON, and the OFF button on the

Lights red

remote control or the SUB POWER

(standby)

 

button on the underside of the

 

 

 

 

front of the frame is OFF.

 

 

 

 

 

When the main power switch is

 

 

ON, and the ON button on the

Lights green

On

remote control or the SUB POWER

 

 

button on the underside of the

 

 

front of the frame is ON.

 

 

 

 

 

When the main power switch is

 

 

ON, and the ON button on the

 

Off

remote control or the SUB POWER

Lights orange

button on the underside of the

(Power Save)

 

front of the frame is ON.

 

 

 

 

However, the state in POWER

 

 

SAVE mode

 

 

 

When the indicating lamp lights in orange or the message “No Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the screen, there is something unusual about the status of reception.

See “Power Save Mode” or “Symptoms That Seemingly Appear to be Failures.”

ATTENTION

Avoid repeatedly turning the monitor on and off at short time intervals. Failures might result from such operation.

Turn off the main power switch before leaving the monitor out of use for an extended period of time.

If a power failure occurs while the main unit is running, it would be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the main unit.

Image 18
Contents 42EDT41 English Important Safety Instructions There are no user serviceable parts inside the monitorRead before operating equipment Features Contents Safety Instructions About the SymbolsBe sure to keep safety ground connection Safety InstructionsBe cautious of the power cord connection Be careful in handling the battery of the remote controlInstallation environment Avoid a high temperature environmentRemove the power cord for complete separation How to view the monitorDo not physically impact the remote control Precautions for the cable connectionPrecaution during transportation Set the sound volume at a suitable levelTrade name Model Number 42EDT41 PW1AComponent Names Main UnitComponent Names Remote control Handling the Remote ControlLoading Batteries Component Names Remote control Anti-tumble measures Installation InstructionsInstallation Securing to a wall or pillarInstallation Instructions Connecting to a PCInstallation Instructions Mounting the Speaker Unit Power Cord ConnectionSpeakers Turning Power On and Off Operating InstructionsIndicating lamp Volume UP/DOWN buttons Operating Instructions Volume AdjustmentInput Switching Audio MuteDisplay area selection diagram RGB input Size SwitchingInput Signal Screen Display Operating InstructionsMenu button Using the Menu Screen On-screen display systemRefer to Concerning the adjustment items Settings OK buttonPicture Menu Timer Menu Audio MenuFunction Menu Setup Menu RGB1 DVI-PC RGB2Automatic Store Other FeaturesLanguage Menu Select a language by Select buttons and press the OK buttonWhen the RGB1, RGB2 input is selected Other Features Signal CheckPower Save Mode Status Display ActionAbout screen defects Image Retention of Plasma DisplayMethods to Reduce the Occurrence of Image Retention About residual imagesSpecifications TroubleshootingSymptoms That Seemingly Appear to be Failures Check the way the signal cable is connectedEnglish Troubleshooting Actions to Correct Abnormal Displays Connecting to a Video Imaging Device With DVI-STB and RGB component setupVideo Unit Function Display size selection diagram Zoom buttonTV AV1 AV2 AV3 RGB2 RGB1 AV4 Full Using a wide-screen monitor PressZoom and Cinema Operating Instructions Displaying Multi Picture Pictures SplitYNR Operating Instructions Picture Menu Cyan Color ManagementMagenta Color DecodingVideo Input SystemColor System AV2 1st stepOperating Instructions Setup Menu Menu Display Registration conditionDuring VCR special playback fast forward, rewind OutputPrecautions when connecting the antenna Tuner Unit Function Installation InstructionsConnecting Antenna Monitor rear panelPanoramic Full Cinema Zoom UP/DOWN buttons Mute button Zoom buttonActivating the Split mode from the TV screen Pictures Split 4 pictures 12 picturesSelect buttons Pictures Display will go out in approximately 6 seconds TV positionName Freeze button Picture FreezingInverse Split StrobeDuring TV mode Operating Instructions Setup Menu Page English Page English Page Other Functions Multi-Channel Telvision SoundOperating Instructions Other Functions DVD Player SelectionExample Intermittent interference Snowy picture poor soundMultiple images sound O.K No picture or soundProduct Specifications Input connector pin specifications Product Specifications Signal InputRGB terminal D-sub 15-pin connector Scart connector pin specificationsProduct Specifications Recommended Signal List With Digital RGB signal input RGB1 inputWith Analog RGB signal input RGB2 input With component input AV1, AV2 and RGB2-component input Signal mode Horizontal Dot clock Remarks Signal NameWith R, G, B Video input AV2 and AV4 input Vertical frequencyRemarque On L5N 2L8, Canada