Hitachi P42T501 Remote for VCR/PVR Functions, Precoded VCR/PVR Buttons, MY VCR/PVR Code is

Page 35

The Remote for VCR/PVR Functions

OPERATING THE PRECODED FUNCTION FOR YOUR VCR/PVR (Personal Video Recorder).

This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to

match the remote system of your VCR/PVR (refer to pages 37-38 for pre-codes).

1.Turn ON your VCR/PVR.

2.To switch to VCR/PVR pre-coded mode, use the SOURCE SELECT button on the remote control to position the LED light to the corresponding selection PVR/VCR.

3.Hold down the SOURCE SELECT button on the remote and enter the four digit preset code that matches your VCR/PVR, as shown on pages 37-38. Release the SOURCE SELECT button. The indicator light will flash 3 times if the code was accepted.

4.Aim the remote at the VCR/PVR and press the POWER button. The remote will turn off your PVR when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your VCR/PVR. If the VCR/PVR does not turn off, try a different four digit preset code.

5.The remote will now control your VCR/PVR.

NOTE: 1. If your VCR/PVR cannot be operated after performing the above procedures, your VCR/PVR code has not been precoded into the remote.

2.In the unlikely event that your VCR/PVR cannot be operated after performing the above procedures, please consult your VCR/PVR operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

PRECODED VCR/PVR Buttons

These buttons transmit the chosen precoded VCR/PVR codes :

-Power	-Cursor & Select	-Enter
-Menu	-Channel Up & Down	-Dash (-)
-Exit	-Number PAD	-Play,Pause,Stop
-Info	-Last CH	-FWD,Skip FWD
-Record	-RWD

EXCLUSIVE TV Buttons

These buttons are for operating the TV :

	-Day/Night	-CC	-Inputs (only if
	-Aspect	-Vol Up & Down	programmed,
			refer to page 36)
	-PIP	-Mute

MY VCR/PVR CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.

The Remote Control

35

Image 35

Contents Plasma Television Read Before Operating Equipment Important Safety InstructionsFor More INFORMATION, Call 1-800-HITACHI For U.S. models AccessoriesRemote Control Battery Installation and Replacement Location How To Set Up Your New Hitachi Plasma TelevisionSecuring to a Wall AntennaAC Cord Installation Instruction Step Setting for Wall Mounting on 50 & 55 ModelsRemove these 2 screws First to separate the TV Antenna Connections to Rear Jack Panel ViewingHook-up Cables and Connectors SAT Quick Reference Remote Control Buttons and FunctionsCBL SD Card Photo Input Upgrade CardFront Panel Controls INPUT-FRONT Jacks Power light indicatorRemote Control sensor Monitor OUT & Audio OUT Rear Panel ConnectionsFront Input Panel Connecting External Video SourcesTime use Digital Tips on Rear Panel Connections Installation RecommendationConnecting AN S-VIDEO and Stereo Audio Source to Input Hdmi input Connecting External Audio/Video Devices Connecting Monitor OUT Connecting AN External Audio AmplifierRemote Control Source Select button How to Use the Remote to Control Your TVPower button ZOOM1/ZOOM2 StandardExpanded Hdmi Analog ChannelsDigital Channels Photo Input Cursor PADRotate Channel SELECTOR/FAVORITE Channel WhitePIP button Split Mode PICTURE-IN-PICTUREPicture-In-Picture PIP Strobe Freeze Pause buttonMain Freeze Split FreezeExclusive TV buttons Remote Control for Cable Box FunctionsOperating the Precoded Function for Your Cable BOX Precoded Cable BOX buttonsSET-TOP-BOX Code is Remote Control for Set-Top-Box/Satellite Receiver FunctionsPrecoded SET-TOP-BOX/SATELLITE Receiver buttons MY Satellite ReceiverPrecoded DVD Buttons Remote Control for DVD FunctionsOperating the Precoded Function for Your DVD Player DVDMY VCR/PVR Code is Remote for VCR/PVR FunctionsPrecoded VCR/PVR Buttons Input Access How to Use the Source Select ButtonCable Brand Codes Remote Control CodesPVR Brand On-Screen Display Video Video Mpeg NR Mode Reset Video SettingsAspect Auto AspectAudio DRC Auto Channel Scan Signal MeterStart or Reset option Channel ManagerChannel List Engage Lock Change Access CodeLocks Motion Picture Ratings Table Movie RatingsTV Parental Guide Ratings Table TV RatingsCanadian Ratings English Table Canadian Ratings EngCanadian Ratings French Chart Info RegionMONTH, DAY, and Year Use the Cursor PAD TimersSet The Clock 300 Set Sleep TimerSet Day/Night Timer Select Start Time AM/PM Use the Cursor PAD Set Event TimerEvent 2, Event 3, Event 4 and then press Select Start Time HOUR/MINUTE Use the Cursor PADSet The Language SetupSet The Menu Options Set The Screen Saver Image PowerAutomatic Power Saving Set The Menu BackgroundOff Set The InputsInput 3 Auto Link AutoAnalog Captions Caption ModeSet The Closed Captions Caption DisplaySet The Quick Start Options Reset The SoftwareUpgrade NOW Reset TV SettingsDo not Equipment Care and TroubleshootingTroubleshooting Switch ON/OFFReception Problems Plasma Television Troubleshooting TroubleshootingFCC Information Useful InfoFeatures Features and SpecificationsRear View, Use as Reference for Wall Mount Bracket Set DimensionsInch Models Includes Table Top Stand Weight lbs./kg 116.7/53 10-1/8 Meadowpine Blvd Mississauga, Ontario L5N 6C3 HitachiHome Electronics Division Canada 1-800-HITACHIService Information Page END User License Agreement for Hitachi DTV Software End User License Agreement for Hitachi DTV SoftwareOperating System License Information End User License Agreement for Operating System SoftwareGNU General Public License Version 2, June No Warranty END of Terms and Conditions GNU Lesser General Public License Version 2.1, February 150 151 Agreements Appendix a AppendixesAppendixes Closed Captions Index156 157 QR70203