Hitachi L26D205 Checking the digital signal strength, Labeling channels, Labeling video inputs

Checking the digital signal strength

This TV will allow you to view the digital signal meter for digital channels.

1 Select “Channel”, then press ▶ or ENTER.

2 Press ▲ or ▼ to select “Signal Meter”.

3 Press ▶ or ENTER to check the digital signal strength. The digital signal strength screen will appear.

If necessary, adjust the direction of the antenna to obtain the maximum signal strength.

CH Signal Meter

0 50 100

Signal Level

NOTE:

• Signal meter feature is not available for analog channels.

• After 240 seconds, the Signal Meter screen will clear and the TV will return to normal viewing automatically.

Labeling channels

Channel label appears with the channel number display each time you turn on the TV, select a channel, or press DISPLAY. You can choose any four characters to identify a channel.

To create channel labels

1 Select “Channel”, then press ▶ or ENTER.

2 Press ▲ or ▼ to select “Channel Labels”, then press ▶ or

ENTER.

The Channel Labels menu will appear.

3 Press ◀ or ▶ to select a channel you want to label, then press ▼.

CH Channel Labels

Channel Number	15-1
Channel Label	CH-1
Label Clear	>>
:Move	:Adjust

Press ◀ or ▶ repeatedly until the character you want appears
4 in the first space.
			Channel Labels
	CH
		Channel Number			15-1
		Channel Label				CH-1
		Label Clear			>>
			:Move	:Adjust	ENTER :Select

The characters rotation as follows:

- , () @ / + = -

SPACE

If the character which you desire appears, press ENTER. Repeat this step to enter the rest of the characters.

If you would like a blank space in the label name, you must choose the empty space from the list of characters.

20

56P5021A_eng.indd 20

5 Repeat steps 3-4 for other channel.You can assign a label to each channel.

6 When you finish inputting the label name, press EXIT to return to the normal screen.

To clear a Channel Label

After step 3 above, press ▲ or ▼ to select “Label Clear”, then press ▶ or ENTER.

NOTE:

• The channel labels will be reset after “Scan” on page 19.

Labeling video inputs

The Video Label feature allows you to label each input source for your TV.

1 Select “Setup”, then press ▶ or ENTER.

2 Press ▲ or ▼ to select “Video Label”, then press ▶ or ENTER. 3 Press ▲ or ▼ to select an input which you want to label.

4 Press ◀ or ▶ to select the desired label for that input source.

Video Label

Video1-

Video2-

Component-

HDMI1-

HDMI2-

PC-

:Move :Adjust

Available video labels: – / VCR / DVD / STB / Cable / Satellite / Receiver / Game / Camcorder / PC / DVI PC / Blu-ray

Setting the Parental Control

An age limitation can be set to restrict children from viewing or hearing violent scenes or pictures that you may choose to exclude. The restriction applies to “TV” and “Movie” if this data is transmitted. You may set this restriction separately. To use the Parental Control function, you must register a password.

To register a password

1 Select “Locks”, then press ▶ or ENTER.

2 Select and enter your password (4 digits) using Number buttons (0-9), then press ENTER.

Locks

New Password * * *_

	[0-9] :Enter Code	ENTER :Select
3	“ ” appears instead of the number.
	Enter the same password again to confirm, then press
	ENTER.
	The password is now registered.

NOTE:

• If you forget the password, contact Customer Service at 1-800- 289-0981 (USA), 01-800-703-0885 (MEXICO) for assistance. Your original remote control will be required.

• To avoid forgetting the password, write it down and keep in a safe place.

5/21/11 3:21:31 PM