Monster Cable HTPS 7000 MKII owner manual Outlet Programming

Page 19

HOOK-UP GUIDE

Outlet Programming

All PowerSource outlets on the rear panel are programmable via the menu and select buttons on the front panel. To set up each outlet pair, use the front panel MENU and SELECT buttons to choose between SWITCHED ON, SWITCHED ON AFTER DELAY and UNSWITCHED (Always On) independently for each outlet pair. You can change the settings, whenever you like. Using the outlet pair labeled ANALOG FILTER as an example, the following diagrams illustrate how it’s done:

A)Power up the PowerSource: Press the ON/OFF switch one time to power the unit and start the process. Once the PowerSource is on, the display will show the AC line voltage as in Figure 1.

NOTE: The power-on process may take up to 60 seconds since any outlet pair can be configured

as SWITCHED ON AFTER DELAY. You can see any outlet pair’s power status by referring to its indicator on the front panel.

B)Set Outlet Pair to SWITCHED ON: Press MENU until the second line display shows the status of the ANALOG outlet pair. Press the SELECT button until the time delay changes to 0 (zero), as in Figure 2.

The 0 (zero) time delay setting indicates SWITCHED ON mode for the ANALOG outlet pair. This pair will be live once the PowerSource is powered up by pressing the front panel ON/OFF button, or triggered by an external signal.

14

Image 19

Contents Signature Htps 7000 Mkii Table of Contents Important Safety Information Page Important Note Proper Power and Protection Proper Grounding and InstallationNoel Lee Dear EnthusiastHead Monster Or above 132Vrms MONSTER’S Exclusive T2 TechnologyMONSTER’S Patented Clean Power Stages Minds Behind the Monster Powersource Design 3IGNATURE /*-ÇäääÊ Monster Signature Htps 7000 Mkii Powersource FeaturesRear Signature Htps 7000 Mkii Powersource Features Page Digital Outlet Hook-Up HOOK-UP GuideDigital Outlets Video Outlets Video Outlet Hook-UpAnalog Audio Outlets Analog Audio Outlet Hook-UpUse a corresponding outlet for best performance High Current Audio Outlets Ultra-High Current Audio Outlet Hook-UpOutlet Programming Or when triggered by an external signal Over-Voltage and Under-Voltage Audible Alarm Setting Over-Voltage and Under-Voltage Automatic Shutdown Setting Coaxial Connections Hook-Up Protect Phone/Network Line Connections as Follows Phone/Network Connections Hook-UpRemote AC In Control Hook-Up Remote DC In Control Hook-UpTo Control Components Remote DC Out Control Hook-UpSymptom Possible Cause Remedy TroubleshootingGrounded, attach a copper wire Turn the PowerSource OnUnswitched outlet Turn the component power OnYou wish to use to activate Unswitched LEDSwitched LED is Off Plug the plug into the componentIs emitting a loud Indicator on front Same as Switched and haven’t pluggedTimed On Panel is OffSignature Htps 7000 Mkii Powersource Page Page Manual de l’utilisateur Table DES Matières Mise EN Garde Liquides Éviter les chocs électriques Importantes Informations DE SécuritéMise EN Garde Sources d’alimentation Mise EN Garde Mise à la terre et polarisationMise EN Garde Précautions en cas d’orage Mise EN Garde Sécurité du cordon d’alimentationMise EN Garde Mise à la terre adéquate Mise À LA Terre ET Installation AdéquatesRemarque importante Protection et alimentation adéquates Cher passionné Direction de Monster Technologie T2 Exclusive À Monster Étages Brevetés Clean Power DE Monster LES Cerveaux Derrière LE Concept Powersource DE Monster VUE Avant VUE Spécifications DU Powersource Signature Htps 7000 Mkii De vos appareils Raccordement aux prises numériques Guide DE RaccordementPrises Numériques Prises Vidéo Raccordement aux prises vidéoPrises Audio Analogiques Raccordement aux prises audio analogiquePrises Audio de Puissance Raccordement aux prises audio de puissanceProgrammation de sortie Guide DE Raccordement Réglage de l’alarme sonore de surtension et de sous-tension Guide DE Raccordement Raccordement aux connexions coaxiales Protégez les connexions téléphonique/réseau comme suit Raccordement aux connexions téléphonique/réseauProgrammées s’allument après le délai imparti Vers les appareils de contrôle Dépannage Émettent un PowerSource est allumé Les haut-parleursUn appareil branché Allumez l’appareilDistance est trop faible La DEL de la prise nonCommutée est éteinte Commutées est éteinte Des prises à distance sans avoirBranchez la prise électrique du PowerSource dans l’appareilLe PowerSource Votre installation12V c.c mA 15A/1800W Phase-Neutre P-NPhase-Terre P-T Neutre-Terre N-T 30V c.c