Crown 460CSL Test 14 Odep Limiting, Test 15 LF Protection, Test 16 Signal to Noise Ratio

Page 15

Power Base-1 & 460CSL Amplifier Service Manual

Checkout Procedures

Procedure Capacitive: Load each channel to 8 ohms in parallel with 2 µF. Inject a 20 kHz sine wave with 30 VAC output for 10 seconds.

Procedure Inductive: Load each channel to 8 ohms in parallel with 159 µHenries. Inject a 1 kHz sine wave with 15 VAC output for 10 seconds.

Procedure Torture: Load each channel with the primary (red and black leads) of a DC-300A transformer (D 5781-6). Inject a 10 Hz sine wave at sufficient output level to cause 3 to 5 flyback pulses, for 10 seconds. Procedure Short: Inject a 60 Hz sine wave at 5 VAC. After establishing signal, short the output for 10 sec- onds.

TEST 14: ODEP LIMITING

Spec: No oscillation on ODEP Limiting wave form; either channel controls limiting in Parallel Mono Mode. Initial Conditions: Controls per standard; rag or other obstruction blocking fan so that it does not turn.

Procedure: Load the amplifier to 2 ohms on each channel. Inject a 60 Hz sine wave and adjust for 15 Vrms at the output. After a few minutes observe a wave form similar to Figure 4. Remove the input signal from both channels and allow the amplifier to cool for a few minutes. Switch the amplifier to Parallel Mono and remove the load from Channel 1. Inject the signal into Channel 1 and observe that ODEP limiting occurs at the output of both channels. Remove the load from Channel 2, and install the load on Channel 1. Again, observe that both channels limit. Return all amplifier controls to standard initial conditions. Remove the fan obstruction.

Figure 4. ODEP Limiting Wave Form

TEST 15: LF PROTECTION

Spec: Amplifier mutes for low frequency.

Initial Conditions: Controls per standard.

Procedure: No load. Inject a 0.5 Hz 6 volt peak-to-peak square wave into each channel and verify that each channel cycles into mute.

TEST 16: SIGNAL TO NOISE RATIO

Spec: 100 dB (105 dB A-weighted) below rated 8 ohm power.

Initial Conditions: Controls per standard. Short inputs.

Procedure: Load each channel to 8 ohms. Measure less than 400 µV at the output of each channel (or –100 dB from reference of +34.25 dBu).

TEST 17: TURN ON TRANSIENTS

Spec: No dangerous transients.

Initial Conditions: Controls per standard.

Procedure: From an off condition, turn on the amplifier and monitor the output noise at the time of turn on. Note: Turn on noise may increase significantly if the amplifier is cycled off and on.

TEST 18: TURN OFF TRANSIENTS

Spec: No dangerous transients.

Initial Conditions: Controls per standard.

Procedure: From an on condition, turn off the amplifier and monitor the output noise at the time of turn off. Note: Turn off noise may increase significantly if the amplifier is cycled off and on.

TEST 19: INTERMODULATION DISTORTION

Spec at 0 dB Output: 0.01%.

Spec at –35 dB Output: 0.05%.

Initial Conditions: Controls per standard.

Procedure: Load each channel to 8 ohms. Inject a SMPTE standard IM signal (60 Hz and 7 kHz sine wave mixed at 4:1 ratio) at 200 Watts (32.4 VAC). With an IM analyzer measure less than 0.01% IMD. Repeat test at –35 dB (reference 200 Watts or 32.4 VAC) and mea- sure less than 0.05% IMD.

TEST 20: CLIPPING

Spec: No protective action during test.

Initial Conditions: Controls per standard.

Procedure: Load each channel to 8 ohms. Inject a 1 kHz sine wave at each input and drive output 6 dB into clip for 10 seconds. The amplifier should not activate any protective circuits (ODEP, Fault, or LF Protection).

POST TESTING

After completion of testing, if all tests are satisfactory,

the amplifier controls should be returned to the posi- 15 tions required by customer. If conditions are unknown

or unspecified, factory settings are as follows:

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Power BASE-1& 460CSL Avis Table of Contents Warranty IntroductionScope Parts Mechanical SpecificationsPower PerformanceBLU Voltage ConversionFront END Operation FeaturesTheory OverviewVoltage Translators Error AmpHigh Side HS Grounded Bridge TopologyLow Side LS Output Device Emulation Protection OdepPositive Standard Initial Conditions Checkout ProceduresTest 2 Output Bias Adjustment Test 3 Odep Voltage AdjustmentTest 12 Output Power Test 4 AC Power DrawTest 5 Common Mode Rejection Test 7 Phase ResponseTest 15 LF Protection Test 16 Signal to Noise RatioPost Testing Test 14 Odep LimitingCheckout Procedures Mechanical Non-Module Parts Output Assembly ONE PER Channel Back Panel AssemblyChassis Front Assembly Main Chassis Assembly Main Modules Module InformationModule History Output ModulesQ42576-1 Output Module Parts List P10137-1 Board Q42661-1 Output Module 4 Resistor #2 for PB-1 Q42661-1 Output Module Parts List P10137-1 BoardQ42718-9 Output Module 4 Resistor #3 for PB-1 Q42718-9 Output Module Parts List P10233-8 BoardQ42885-6 Output Module Parts List P10305-4 Board Q42967-2 Output Module Parts List P10341-9 Board Q43200-7 Output Module Parts List P10397-1 Board Q42552A0 Main Module Parts List D 6304B2 Board Network ResistorsQ42552A0 Main Module Original for PB-1 IC’S SwitchesQ42664-5 Main Module Parts List D 6910-0 Board UPA75 PNP Q42682-7 Main Module #2 for PB-1 Q42682-7 Main Module Parts List D 6910-0 BoardTrim POT InterconnectsBoard Mounts U1, U2 Q42776-7 Main Module 3rd Gain for PB-1 Q42776-7 Main Module Parts List D 7251-8 BoardDpdt Side Header 5 PIN Q42953-2 Main Module Parts List D 7251-8 Board UPA75 Misc Q43060-5 Main Module Parts List D 7993-5 Board Jumper 7325-1 Ground Lift 7960-5 Sensitivity 6781-6 Stereo/Mono

460CSL specifications

The Crown 460CSL is a powerful combination of innovation and performance that redefines efficiency in the material handling industry. Designed for heavy-duty tasks, this electric lift truck offers an impressive range of features that cater to the demands of modern warehouses and distribution centers.

One of the standout characteristics of the Crown 460CSL is its advanced ergonomic design, which prioritizes operator comfort and productivity. The spacious operator compartment is designed to minimize fatigue during extended use, featuring a low step-in height for easy access and a fully adjustable seat that provides optimal support. The intuitive controls are positioned for easy reach, allowing operators to maneuver the lift truck with ease and precision.

At the heart of the Crown 460CSL is its robust AC motor technology. This powerful motor provides rapid acceleration and smooth operation, reducing both energy consumption and maintenance needs. The regenerative braking system helps to extend battery life by converting braking energy back into stored energy, making the lift truck more efficient during operations. Operators benefit from enhanced traction and stability, ensuring dependable performance on various surfaces.

The Crown 460CSL boasts industry-leading lifting capabilities, with a maximum lifting capacity often exceeding competitors. Its precision-engineered mast allows for smooth and steady lifting of heavy loads, while its advanced hydraulic system provides reliable control over load placement. The lift’s extended height options enable operators to handle tasks at varying elevations, from ground level to tall shelving systems, with confidence.

Safety is a top priority for Crown, and the 460CSL incorporates several features designed to protect both operators and the loads being handled. The truck is equipped with a comprehensive suite of safety features, including an integrated stability system, load monitoring capabilities, and a visibility-enhancing overhead guard. These features work together to provide operators with greater awareness of their surroundings, reducing the risk of accidents.

In terms of technology, the Crown 460CSL integrates advanced diagnostics and connectivity features. This enables fleet managers to monitor performance, track usage patterns, and schedule maintenance with ease. Remote access to diagnostic information ensures that any potential issues can be identified and resolved promptly, further enhancing the truck's reliability and efficiency.

In conclusion, the Crown 460CSL stands out in the crowded lift truck market due to its combination of ergonomic design, powerful motor technology, impressive lifting capabilities, and enhanced safety features. This electric lift truck is an excellent choice for businesses seeking to improve productivity and reduce operational costs while maintaining a safe and comfortable working environment for their operators.
Top Page Image Contents