Extron electronic setup guide TLP 1000MV and TLP 1000TV Setup Guide, Overview

Page 1

TLP 1000MV and TLP 1000TV • Setup Guide

Overview

 

 

 

 

 

 

 

 

:

 

 

 

 

 

 

 

 

ANT

 

for

 

 

 

 

 

T

 

 

.com

 

 

 

 

 

 

 

 

 

 

IMPOR.

 

on

Series

 

 

 

 

extr

 

 

 

 

towww

 

 

 

1000

 

 

.

 

 

 

 

 

 

connecting

Refer

 

TLP

 

 

 

ce

 

 

 

 

e

 

sour

 

 

completebefor

 

 

 

 

 

the guide

thepower

 

 

user

 

to

 

 

 

 

 

 

 

 

the

product

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Extron TLP 1000MV (wall-mounted) and TLP 1000TV (desk-mounted) TouchLinkPanels provide simple and versatile configuration and control for a range of IP Link® control systems. Graphic and text objects are displayed on the screen. These objects have system control functions associated with them and the touch overlay allows you to activate or regulate those functions.

These touchpanels communicate through an Ethernet connection to a configurable IP Link control processor. Video and audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must be connected to a network switch, hub, or router that is connected to an Ethernet

LAN or the Internet. An Extron IP Link controller must also be connected to the same network. Suggested models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR48, IPL T SFI244, or IPCP 505.

Extron strongly recommends that power is provided by a Power over Ethernet (PoE) power supply.

This guide provides basic instructions for experienced installers to mount and perform initial configuration on the

TLP 1000 series of touchpanels. Full instructions and reference material can be found in the TLP 1000MV and TLP 1000TV User Guide, which is available on the Extron website (www.extron.com).

Front Panel Features

7

7

4

 

5

 

1

 

1

 

 

2

6

2

 

 

3

 

3

4

5

6

Extron TLP 1000MV

Extron TLP 1000TV

AMotion Sensor — when no motion has been detected for a user-defined period of time, the unit goes into sleep mode. When motion is detected by the sensor, the screen display is restored and active.

BMicrophone — is located below the LCD screen.

CConnection status LED — is unlit during normal operation. The LED blinks red if the connection to the IP Link controller is lost.

DProgrammable LEDs — one on each top corner can be programmed to provide system feedback. They light red or green and can blink or light solid.

ELCD screen — has a 1024x600 resolution with a touch overlay. Extron software is used to design and configure a graphic user interface to display buttons, text, or icons, which have user‑defined functions associated with them.

FSpeakers — Two speakers placed under the screen, on either side of the panel, provide audible feedback for the user.

GLight Sensor — (can only be seen from above the unit) monitors ambient light level and adjusts screen brightness.

1

Image 1
Contents Front Panel Features TLP 1000MV and TLP 1000TV Setup GuideOverview Rear Panel Features TLP 1000MV Reset Buttons and LEDCalibration Menu Initial ConfigurationMounting Options TLP 1000MVReset Modes TLP 1000MV and TLP 1000TV Setup Guide Cont’dScreen Design and Configuration Wall-Mounting or Furniture-Mounting the TLP 1000MV