Sound
Before you begin:
You must set Home in Location. ➠ p. 27
Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode.
1Press MENU and use ▲▼ to select Sound, then press OK.
Picture | Auto sound | Standard |
Sound | Equalizer |
|
Setup | SRS TruSurround XT | On |
Features | Auto volume leveling | Off |
Language | TV speakers | On |
USB | Primary MTS | Stereo |
|
|
|
2Use ▲▼◄► to select the item you want to adjust, then press OK.
| to select the desired setting, then press OK. | |
| (Personal, Standard, Vivid, Sports, Movie, Music and | |
Auto sound | News) | |
When you adjust the following settings (Equalizer, | ||
| ||
| SRS TruSurround XT and Auto volume leveling), | |
| Personal will be set automatically. |
Adjust the tonal quality for each frequency.
| Cursor ◄ | Cursor ► |
Equalizer | to adjust the each level of tonal quality | |
| Press BACK to go back to the previous menu. | |
This selects sound modes for more spatial or surround sound reproduction.
SRS TruSurround XT | Off | to set SRS TruSurround XT® to Off | |
On | to set SRS TruSurround XT® to On | ||
| |||
|
|
|
This function keeps a constant loudness differential between the TV commercials and the programs.
Auto volume | Off | to remove the auto volume leveling |
|
| |
| to reduce volume differences between | |
leveling | On | |
|
| the TV commercials and the programs |
You can select the Audio Output from the unit’s speakers or not. If your amplifier is HDMI link function compatible and connected by an HDMI cable to this unit, some sound operations such as volume up can be changed by using this unit’s remote control. Make sure
| On | to output sound from the unit’s | |
| speakers | ||
|
| ||
|
|
| |
| Off | not to output sound from the unit’s | |
TV speakers | speakers | ||
| |||
CEC Link | to control Audio Output from your | ||
| |||
| connected | ||
|
| with VOL + / − by using this unit's | |
|
| remote control. |
You can set the output mode as a default for the sound mode (Analog TV only).
This setting is not interlocked when you change the output mode by pressing SAP. Refer to Switching audio mode. ➠ p. 15
| Stereo | to output |
Primary MTS | Mono | to output |
|
|
|
| SAP | to output second audio program |
20 English
Setup
Before you begin:
Make sure the unit is connected to antenna or cable.
1Press MENU and use ▲▼ to select Setup, then press OK.
Picture | Autoprogram |
Sound | Channel list |
Setup | Add channels |
Features | Antenna |
Language |
|
USB |
|
|
|
2Adjust the following items.
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are registered with your cable TV provider when you install Cable channels.
1 Use ▲▼ to select Autoprogram, then press OK.
• If you run Autoprogram when you have locked channels, a message appears asking to enter your PIN . Enter your PIN in order to complete the installation.You need to set the channel lock again after the installation.
2 Use ▲▼ to select an appropriate option, then press OK.
––When Antenna is selected, the TV detects antenna signals. It searches for DTV and Analog TV channels available in your area.
––When Cable is selected, theTV detects signals supplied by cable. It searches for DTV,AnalogTV and Cable channels available in your area.
| Picture | Autoprogram will rescan all channels. | Back |
| ||
| Sound | Auto programming may take more than 20 | Antenna |
| ||
| minutes to complete. |
| ||||
| Setup | |
|
| Cable |
|
| Features | Select your signal source. |
|
| ||
| Language | Antenna |
|
|
|
|
| USB |
|
|
|
|
|
|
| Cable | Or | ANTENNA IN |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Continued on next page. | |||