Magnavox 51MP6200D user manual Convergence, Using Manual Converge Multipoint Red/Blue

Settings
Setup	4		Convergence
Preferences			Manual convergence
Source
Clock
Convergence
	Settings		Setup
	Convergence				Manual convergence		7
	Manual convergence				Convergence red
					Convergence blue
					Multipoint red
					Multipoint blue
Settings Setup					Save multipoint
Manual convergence		7	Manual convergence			multipoint
Convergence red					Restore factory
Convergence blue				Start now
Multipoint red
Multipoint blue
Save multipoint
Save undo multipoint
Restore factory

Tip: Allow the TV to warm up for 20 minutes before adjusting convergence. Adjust Converge Red or Converge Blue before using the Multipoint Red/Blue controls.

Settings Setup Convergence

Manual convergence 7		Multipoint red
Convergence red
Convergence blue	Start now
Multipoint red
Multipoint red
Save multipoint
Save undo multipoint
Restore factory

Convergence

Manual Convergence: Converge Red/Blue

You can use the Manual Converge controls to make convergence adjustments to suit your personal preferences or to further fine-tune the picture.

&Select MANUAL CONVERGE in the SETUP menu.

éPress the cursor right button to enter into the manual convergence menu.

“Press the cursor down button and select either CONVERGE RED or CONVERGE BLUE and press the cursor right button.

‘Press OK button to start the manual convergence.

Tip: If various images in the picture have red outlines, select CONVERGE RED. If various images in the picture have blue outlines, select

CONVERGE BLUE.

( Use the cursor right, left, up or down button to adjust the cross hair until the colour outline is gone.The adjustment is automatically saved in the TV’s memory when you exit the adjust mode.

§Press the MENU button to return or the INFO key to switch the menu off.

Check the TV picture. If any colour outlines remain around the images, use the MULTIPOINT RED (for red outlines) or MULTIPOINT BLUE (for blue outlines) control. See the next section for instructions for using those controls.

Using Manual Converge: Multipoint Red/Blue

The Multipoint Red/Blue convergence controls allow you to adjust picture convergence at specific points on the TV screen.

&Select MULTIPOINT RED or MULTIPOINT BLUE in the MANUAL CONVERGE menu.

éPress the cursor right to enter navigate mode.

“Use the cursor left, right, up or down button to move to a cross hair that has a colour outline.

‘Press the INFO button to enter adjust mode.

( Use the cursor left, right, up or down to adjust the cross hair until the colour outline is gone.

Settings Setup Convergence

Manual convergence	7	Save multipoint
Convergence red
Convergence blue		Start now
Multipoint red
Multipoint blue
Save multipoint
Save undo multipoint
Restore factory
Settings Setup Convergence
Manual convergence	7	Save undo multipoint
Convergence red
Convergence blue		Start now
Multipoint red
Multipoint blue
Save multpoint
Save undo multipoint
Restore factory
Settings Setup Convergence
Manual convergence	7	Restore factory
Convergence red
Convergence blue		Start now
Multipoint red
Multipoint blue
Save multpoint
Save undo multipoint
Restore factory

14

Settings Setup Convergence

	Manual convergence	7	Save multipoint
	Convergence red
	Convergence blue		Stored
	Multipoint red
	Multipoint blue
	Save multipoint
	Save undo multipoint
	Restore factory
Settings Setup Convergence
	Manual convergence	7	Save undo multipoint
	Convergence red
	Convergence blue		Saved
	Multipoint red
	Multipoint blue
	Save multpoint
	Save undo multipoint
	Restore factory
	Settings Setup Convergence
	Manual convergence	7	Restore factory
	Convergence red
	Convergence blue		Restored
	Multipoint red
	Multipoint blue
	Save multpoint
	Save undo multipoint
	Restore factory

§Press the INFO button to return to navigate mode.

èRepeat steps 3-6 until all misaligned cross hairs have been adjusted.Then press the MENU button.

!For your multipoint adjustments to be stored in the TV’s memory, you must activate SAVE UNDO MULTIPOINT.

Note: If you are not satisfied with the adjustments you just made and want to start over, you can use the UNDO MULTIPOINT control.This control allows you to undo the adjustments, but only if you use it before saving.

To save your multipoint adjustments: Select SAVE MULTIPOINT and press the cursor right or OK button.

To undo your multipoint adjustments: Select SAVE UNDO MULTIPOINT and press the cursor right or OK button.

To restore the TV’s picture convergence to factory settings, select RESTORE FACTORY and press the cursor right or OK button.

çPress the MENU button to return or the INFO button to switch the menu off.